[Resolvido] Lubuntu não reconhece placa Wireless do ECS A535

[jeffersonsan]

Boa tarde,

Coloquei o Xubuntu no meu desktop e gostei. Tenho um laptop antigo e coloquei o Lubuntu. Funciona bem, conecta automaticamente na conexão a cabo, mas a rede wireless nem dá sinal (o led sinalizador não acende).
Passei o dia inteiro, literalmente, de ontem tentando fazer pegar e nada.
O que encontrei na pesquisa pelo google e aqui no forum dava um resultado relativamente simples:
Bastava instalar o pacote "linux-wlan-ng", via synaptic, que a placa automaticamente funcionaria. Não aconteceu comigo.
Se alguém puder me ajudar a habilitar esta placa, agradeceria muito.

Segue alguns dados:
Lubuntu 10.04
Laptop ECS A535+
Placa AirVast Taiwan IEE 802.11b Prism3 USB
pacotes instalados (somente via synaptic):
linux-wlan-ng 0.29+dfsg-4
linux-wlan-ng-doc 0.29+dfsg-4
linux-wlan-ng-firmware 0.29+dfsg-4
linux-wlan-ng-source 0.29+dfsg-4
prism-usb-firmware-installer 0.29+dfsg-4

Tentei verificar o comando "#iwlist wlan0 scan" e tive como resposta que "inteface doesn't suppot scannig"; com o comando "#iwconfig" me aparece "lo no wireless extensions" e "eth0 no wireless extensions". Com o "#lspci" tive como resposta:

00:00.0 Host bridge: Silicon Integrated Systems [SiS] 740 Host (rev 01)
00:01.0 PCI bridge: Silicon Integrated Systems [SiS] Virtual PCI-to-PCI bridge (AGP)
00:02.0 ISA bridge: Silicon Integrated Systems [SiS] SiS962 [MuTIOL Media IO] (rev 25)
00:02.1 SMBus: Silicon Integrated Systems [SiS] SiS961/2 SMBus Controller
00:02.5 IDE interface: Silicon Integrated Systems [SiS] 5513 [IDE]
00:02.6 Modem: Silicon Integrated Systems [SiS] AC'97 Modem Controller (rev a0)
00:02.7 Multimedia audio controller: Silicon Integrated Systems [SiS] AC'97 Sound Controller (rev a0)
00:03.0 USB Controller: Silicon Integrated Systems [SiS] USB 1.1 Controller (rev 0f)
00:03.1 USB Controller: Silicon Integrated Systems [SiS] USB 1.1 Controller (rev 0f)
00:03.3 USB Controller: Silicon Integrated Systems [SiS] USB 2.0 Controller
00:07.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8169 Gigabit Ethernet (rev 10)
01:00.0 VGA compatible controller: Silicon Integrated Systems [SiS] 65x/M650/740 PCI/AGP VGA Display Adapter

[Tota]

Mas se a placa diz => Placa AirVast Taiwan IEE 802.11b Prism3 USB

Para que o comando <lspci>?

Por que não o comando apropriado?

Código Selecionar Expandir

sudo lsusb

[]'s

[jeffersonsan]

Olá, Tota.

Primeiramente obrigado por responder. Também pensei o mesmo e quando tentei este comando, "lsudb", tive como resposta:
Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 002 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub

É verdade que manjo muito pouco do Linux, mas por ser uma placa que está dentro da máquina eu, ingenuamente, pensei que fosse pcmcia. Quando tentei o comando "lsusb" foi por estratégia de desespero (naquelas de tentar de tudo). De todo modo, o problema continua (e mesmo tendo perguntado continuo aqui batendo cabeça).

Abraço.

[Tota]

Li o manual dele lá na ecs. Tem uma luz de acionamento do wi-fi  lado direito em cima do teclado )

Mas no manual não existe nenhuma referencia de como acionar a placa e logico, acender a luz de aviso.

É por teclado ou botão?

Pois como pudemos ver, sua placa esta desligada ( lsusb+lspci )

Veja isto=> http://ubuntuforum-br.org/index.php?topic=19240.0

Lendo os pacotes, para o 10.04 voce deve instalar: prism2-usb-firmware-installer

prism2-usb-firmware-installer will at the time of its own installation
download the firmware files for the prism2_usb devices from the
upstream code repository and convert them to the format used by the
kernel modules since 2.6.32.

[]ś

[jeffersonsan]

Pois é. Essa luz acende automaticamente. No Windows para acioná-la ou desativá-la, a placa e por consequência o led, o fazia via software.
Quanto ao link, foi esse um dos primeiros que ví. Mas não me ajudou muito, pois para o Luis Mota o problema foi resolvido, pelo que parece, simplesmente instalando o pacote "linux-wlan-ng". Que não foi o meu caso. Além do que, ele teve sucesso sob a versao 7.04 do Ubuntu. Outros usuário da distribuição tiveram problemas com versões mais recentes e nas discussões que ví, não achei, ou não apresentaram, solução.
Sobre o pacote que você me sugeriu, já está instalado aqui, como coloquei no final do primeiro post. Mas também não surtiu efeito, como vimos pelos lspci+lsusb.
Mais uma vez obrigado,
Um abraço.

[Tota]

Só por desencargo de consciencia de em terminal um

Código Selecionar Expandir

sudo dmesg

Veja se encontra sua placa lá.

Se encontrar copie e cole a parte referente a ela aqui.

de também um

Código Selecionar Expandir

sudo lsmod

para ver se os modulos de sua placa foram carregados.

[]'s

[jeffersonsan]

rapaz, saiu muita coisa e eu não entendi muito, mas nas linhas referentes a "usb 3-2" reporta bastante erros. Então no "sudo dmsesg" (se tiver muita coisa eu apago os posts):

Código Selecionar Expandir

[    0.000000] Initializing cgroup subsys cpuset
[    0.000000] Initializing cgroup subsys cpu
[    0.000000] Linux version 2.6.32-21-generic (buildd@rothera) (gcc version 4.4.3 (Ubuntu 4.4.3-4ubuntu5) ) #32-Ubuntu SMP Fri Apr 16 08:10:02 UTC 2010 (Ubuntu 2.6.32-21.32-generic 2.6.32.11+drm33.2)
[    0.000000] KERNEL supported cpus:
[    0.000000]   Intel GenuineIntel
[    0.000000]   AMD AuthenticAMD
[    0.000000]   NSC Geode by NSC
[    0.000000]   Cyrix CyrixInstead
[    0.000000]   Centaur CentaurHauls
[    0.000000]   Transmeta GenuineTMx86
[    0.000000]   Transmeta TransmetaCPU
[    0.000000]   UMC UMC UMC UMC
[    0.000000] BIOS-provided physical RAM map:
[    0.000000]  BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
[    0.000000]  BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
[    0.000000]  BIOS-e820: 00000000000ec000 - 0000000000100000 (reserved)
[    0.000000]  BIOS-e820: 0000000000100000 - 000000000dff0000 (usable)
[    0.000000]  BIOS-e820: 000000000dff0000 - 000000000dff8000 (ACPI data)
[    0.000000]  BIOS-e820: 000000000dff8000 - 000000000e000000 (ACPI NVS)
[    0.000000]  BIOS-e820: 00000000ffee0000 - 00000000fff00000 (reserved)
[    0.000000]  BIOS-e820: 00000000fffc0000 - 0000000100000000 (reserved)
[    0.000000] DMI 2.3 present.
[    0.000000] AMI BIOS detected: BIOS may corrupt low RAM, working around it.
[    0.000000] e820 update range: 0000000000000000 - 0000000000010000 (usable) ==> (reserved)
[    0.000000] last_pfn = 0xdff0 max_arch_pfn = 0x100000
[    0.000000] MTRR default type: uncachable
[    0.000000] MTRR fixed ranges enabled:
[    0.000000]   00000-9FFFF write-back
[    0.000000]   A0000-BFFFF uncachable
[    0.000000]   C0000-DFFFF write-protect
[    0.000000]   E0000-EFFFF uncachable
[    0.000000]   F0000-FFFFF write-protect
[    0.000000] MTRR variable ranges enabled:
[    0.000000]   0 base 000000000 mask FF8000000 write-back
[    0.000000]   1 base 008000000 mask FFC000000 write-back
[    0.000000]   2 base 00C000000 mask FFE000000 write-back
[    0.000000]   3 disabled
[    0.000000]   4 disabled
[    0.000000]   5 disabled
[    0.000000]   6 disabled
[    0.000000]   7 base 0D0000000 mask FFE000000 write-combining
[    0.000000] x86 PAT enabled: cpu 0, old 0x7040600070406, new 0x7010600070106
[    0.000000] Scanning 0 areas for low memory corruption
[    0.000000] modified physical RAM map:
[    0.000000]  modified: 0000000000000000 - 0000000000010000 (reserved)
[    0.000000]  modified: 0000000000010000 - 000000000009fc00 (usable)
[    0.000000]  modified: 000000000009fc00 - 00000000000a0000 (reserved)
[    0.000000]  modified: 00000000000ec000 - 0000000000100000 (reserved)
[    0.000000]  modified: 0000000000100000 - 000000000dff0000 (usable)
[    0.000000]  modified: 000000000dff0000 - 000000000dff8000 (ACPI data)
[    0.000000]  modified: 000000000dff8000 - 000000000e000000 (ACPI NVS)
[    0.000000]  modified: 00000000ffee0000 - 00000000fff00000 (reserved)
[    0.000000]  modified: 00000000fffc0000 - 0000000100000000 (reserved)
[    0.000000] initial memory mapped : 0 - 00c00000
[    0.000000] init_memory_mapping: 0000000000000000-000000000dff0000
[    0.000000] Using x86 segment limits to approximate NX protection
[    0.000000]  0000000000 - 0000400000 page 4k
[    0.000000]  0000400000 - 000dc00000 page 2M
[    0.000000]  000dc00000 - 000dff0000 page 4k
[    0.000000] kernel direct mapping tables up to dff0000 @ 10000-15000
[    0.000000] RAMDISK: 09b71000 - 0a833c85
[    0.000000] ACPI: RSDP 000faf70 00014 (v00 AMI   )
[    0.000000] ACPI: RSDT 0dff0000 00028 (v01 AMIINT SiS740XX 00001000 MSFT 0100000B)
[    0.000000] ACPI: FACP 0dff0030 00081 (v01 AMIINT SiS740XX 00000011 MSFT 0100000B)
[    0.000000] ACPI: DSDT 0dff00c0 03575 (v01    SiS      740 00000100 MSFT 0100000E)
[    0.000000] ACPI: FACS 0dff8000 00040
[    0.000000] 0MB HIGHMEM available.
[    0.000000] 223MB LOWMEM available.
[    0.000000]   mapped low ram: 0 - 0dff0000
[    0.000000]   low ram: 0 - 0dff0000
[    0.000000]   node 0 low ram: 00000000 - 0dff0000
[    0.000000]   node 0 bootmap 00011000 - 00012c00
[    0.000000] (9 early reservations) ==> bootmem [0000000000 - 000dff0000]
[    0.000000]   #0 [0000000000 - 0000001000]   BIOS data page ==> [0000000000 - 0000001000]
[    0.000000]   #1 [0000001000 - 0000002000]    EX TRAMPOLINE ==> [0000001000 - 0000002000]
[    0.000000]   #2 [0000006000 - 0000007000]       TRAMPOLINE ==> [0000006000 - 0000007000]
[    0.000000]   #3 [0000100000 - 00008d9e98]    TEXT DATA BSS ==> [0000100000 - 00008d9e98]
[    0.000000]   #4 [0009b71000 - 000a833c85]          RAMDISK ==> [0009b71000 - 000a833c85]
[    0.000000]   #5 [000009fc00 - 0000100000]    BIOS reserved ==> [000009fc00 - 0000100000]
[    0.000000]   #6 [00008da000 - 00008dd128]              BRK ==> [00008da000 - 00008dd128]
[    0.000000]   #7 [0000010000 - 0000011000]          PGTABLE ==> [0000010000 - 0000011000]
[    0.000000]   #8 [0000011000 - 0000013000]          BOOTMAP ==> [0000011000 - 0000013000]
[    0.000000] Zone PFN ranges:
[    0.000000]   DMA      0x00000010 -> 0x00001000
[    0.000000]   Normal   0x00001000 -> 0x0000dff0
[    0.000000]   HighMem  0x0000dff0 -> 0x0000dff0
[    0.000000] Movable zone start PFN for each node
[    0.000000] early_node_map[2] active PFN ranges
[    0.000000]     0: 0x00000010 -> 0x0000009f
[    0.000000]     0: 0x00000100 -> 0x0000dff0
[    0.000000] On node 0 totalpages: 57215
[    0.000000] free_area_init_node: node 0, pgdat c0798720, node_mem_map c1001200
[    0.000000]   DMA zone: 32 pages used for memmap
[    0.000000]   DMA zone: 0 pages reserved
[    0.000000]   DMA zone: 3951 pages, LIFO batch:0
[    0.000000]   Normal zone: 416 pages used for memmap
[    0.000000]   Normal zone: 52816 pages, LIFO batch:15
[    0.000000] Using APIC driver default
[    0.000000] ACPI: PM-Timer IO Port: 0x808
[    0.000000] SMP: Allowing 1 CPUs, 0 hotplug CPUs
[    0.000000] Local APIC disabled by BIOS -- you can enable it with "lapic"
[    0.000000] APIC: disable apic facility
[    0.000000] nr_irqs_gsi: 16
[    0.000000] PM: Registered nosave memory: 000000000009f000 - 00000000000a0000
[    0.000000] PM: Registered nosave memory: 00000000000a0000 - 00000000000ec000
[    0.000000] PM: Registered nosave memory: 00000000000ec000 - 0000000000100000
[    0.000000] Allocating PCI resources starting at e000000 (gap: e000000:f1ee0000)
[    0.000000] Booting paravirtualized kernel on bare hardware
[    0.000000] NR_CPUS:8 nr_cpumask_bits:8 nr_cpu_ids:1 nr_node_ids:1
[    0.000000] PERCPU: Embedded 14 pages/cpu @c1400000 s36024 r0 d21320 u4194304
[    0.000000] pcpu-alloc: s36024 r0 d21320 u4194304 alloc=1*4194304
[    0.000000] pcpu-alloc: [0] 0
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 56767
[    0.000000] Kernel command line: BOOT_IMAGE=/boot/vmlinuz-2.6.32-21-generic root=UUID=e83484c1-dba7-4ca7-a732-f31e91e5e977 ro quiet splash
[    0.000000] PID hash table entries: 1024 (order: 0, 4096 bytes)
[    0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
[    0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
[    0.000000] Enabling fast FPU save and restore... done.
[    0.000000] Enabling unmasked SIMD FPU exception support... done.
[    0.000000] Initializing CPU#0
[    0.000000] allocated 1146240 bytes of page_cgroup
[    0.000000] please try 'cgroup_disable=memory' option if you don't want memory cgroups
[    0.000000] Initializing HighMem for node 0 (00000000:00000000)
[    0.000000] Memory: 204208k/229312k available (4673k kernel code, 24332k reserved, 2122k data, 656k init, 0k highmem)
[    0.000000] virtual kernel memory layout:
[    0.000000]     fixmap  : 0xfff1d000 - 0xfffff000   ( 904 kB)
[    0.000000]     pkmap   : 0xff800000 - 0xffc00000   (4096 kB)
[    0.000000]     vmalloc : 0xce7f0000 - 0xff7fe000   ( 784 MB)
[    0.000000]     lowmem  : 0xc0000000 - 0xcdff0000   ( 223 MB)
[    0.000000]       .init : 0xc07a3000 - 0xc0847000   ( 656 kB)
[    0.000000]       .data : 0xc0590613 - 0xc07a2e48   (2122 kB)
[    0.000000]       .text : 0xc0100000 - 0xc0590613   (4673 kB)
[    0.000000] Checking if this processor honours the WP bit even in supervisor mode...Ok.
[    0.000000] SLUB: Genslabs=13, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[    0.000000] Hierarchical RCU implementation.
[    0.000000] NR_IRQS:2304 nr_irqs:256
[    0.000000] Console: colour VGA+ 80x25
[    0.000000] console [tty0] enabled
[    0.000000] Fast TSC calibration using PIT
[    0.000000] Detected 1194.898 MHz processor.
[    0.004011] Calibrating delay loop (skipped), value calculated using timer frequency.. 2389.79 BogoMIPS (lpj=4779592)
[    0.004060] Security Framework initialized
[    0.004133] AppArmor: AppArmor initialized
[    0.004152] Mount-cache hash table entries: 512
[    0.004483] Initializing cgroup subsys ns
[    0.004494] Initializing cgroup subsys cpuacct
[    0.004503] Initializing cgroup subsys memory
[    0.004526] Initializing cgroup subsys devices
[    0.004532] Initializing cgroup subsys freezer
[    0.004537] Initializing cgroup subsys net_cls
[    0.004583] CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
[    0.004589] CPU: L2 Cache: 256K (64 bytes/line)
[    0.004599] mce: CPU supports 4 MCE banks
[    0.004646] Performance Events: AMD PMU driver.
[    0.004677] ... version:                0
[    0.004681] ... bit width:              48
[    0.004684] ... generic registers:      4
[    0.004688] ... value mask:             0000ffffffffffff
[    0.004692] ... max period:             00007fffffffffff
[    0.004696] ... fixed-purpose events:   0
[    0.004700] ... event mask:             000000000000000f
[    0.004710] Checking 'hlt' instruction... OK.
[    0.021146] SMP alternatives: switching to UP code
[    0.033131] Freeing SMP alternatives: 19k freed
[    0.033204] ACPI: Core revision 20090903
[    0.046656] ACPI: setting ELCR to 0200 (from 0c20)
[    0.048022] ftrace: converting mcount calls to 0f 1f 44 00 00
[    0.048048] ftrace: allocating 21771 entries in 43 pages
[    0.052282] Enabling APIC mode:  Flat.  Using 0 I/O APICs
[    0.052293] weird, boot CPU (#0) not listed by the BIOS.
[    0.052297] SMP motherboard not detected.
[    0.052304] Local APIC not detected. Using dummy APIC emulation.
[    0.052308] SMP disabled
[    0.052934] Brought up 1 CPUs
[    0.052939] Total of 1 processors activated (2389.79 BogoMIPS).
[    0.053619] CPU0 attaching NULL sched-domain.
[    0.054139] devtmpfs: initialized
[    0.056715] regulator: core version 0.5
[    0.056754] Time: 23:20:35  Date: 08/24/10
[    0.056868] NET: Registered protocol family 16
[    0.057157] EISA bus registered
[    0.057189] ACPI: bus type pci registered
[    0.059824] PCI: PCI BIOS revision 2.10 entry at 0xfdb01, last bus=2
[    0.061849] bio: create slab <bio-0> at 0
[    0.062819] ACPI: EC: Look up EC in DSDT
[    0.071462] ACPI: Interpreter enabled
[    0.071475] ACPI: (supports S0 S1 S3 S4 S5)
[    0.071526] ACPI: Using PIC for interrupt routing
[    0.080659] ACPI: EC: GPE = 0x16, I/O: command/status = 0x66, data = 0x62
[    0.080750] ACPI: Power Resource [URP1] (off)
[    0.080807] ACPI: Power Resource [URP2] (off)
[    0.080877] ACPI: Power Resource [FDDP] (off)
[    0.080933] ACPI: Power Resource [LPTP] (off)
[    0.081146] ACPI: No dock devices found.
[    0.082006] ACPI: PCI Root Bridge [PCI0] (0000:00)
[    0.082110] pci 0000:00:00.0: reg 10 32bit mmio: [0xd0000000-0xd1ffffff]
[    0.082339] pci 0000:00:02.0: Enabling SiS 96x SMBus
[    0.082414] pci 0000:00:02.1: reg 20 io port: [0xc00-0xc1f]
[    0.082503] pci 0000:00:02.5: reg 20 io port: [0xff00-0xff0f]
[    0.082580] pci 0000:00:02.6: reg 10 io port: [0xd400-0xd4ff]
[    0.082593] pci 0000:00:02.6: reg 14 io port: [0xd000-0xd07f]
[    0.082658] pci 0000:00:02.6: supports D1 D2
[    0.082664] pci 0000:00:02.6: PME# supported from D3hot D3cold
[    0.082672] pci 0000:00:02.6: PME# disabled
[    0.082733] pci 0000:00:02.7: reg 10 io port: [0xdc00-0xdcff]
[    0.082745] pci 0000:00:02.7: reg 14 io port: [0xd800-0xd87f]
[    0.082810] pci 0000:00:02.7: supports D1 D2
[    0.082814] pci 0000:00:02.7: PME# supported from D3hot D3cold
[    0.082821] pci 0000:00:02.7: PME# disabled
[    0.082861] pci 0000:00:03.0: reg 10 32bit mmio: [0xcfff9000-0xcfff9fff]
[    0.082946] pci 0000:00:03.1: reg 10 32bit mmio: [0xcfffa000-0xcfffafff]
[    0.083048] pci 0000:00:03.3: reg 10 32bit mmio: [0xcfffb000-0xcfffbfff]
[    0.083118] pci 0000:00:03.3: PME# supported from D0 D3hot D3cold
[    0.083126] pci 0000:00:03.3: PME# disabled
[    0.083194] pci 0000:00:07.0: reg 10 io port: [0xcc00-0xccff]
[    0.083207] pci 0000:00:07.0: reg 14 32bit mmio: [0xcfff8f00-0xcfff8fff]
[    0.083247] pci 0000:00:07.0: reg 30 32bit mmio pref: [0xcffc0000-0xcffdffff]
[    0.083277] pci 0000:00:07.0: supports D1 D2
[    0.083281] pci 0000:00:07.0: PME# supported from D1 D2 D3hot D3cold
[    0.083288] pci 0000:00:07.0: PME# disabled
[    0.083401] pci 0000:01:00.0: reg 10 32bit mmio pref: [0xc0000000-0xc7ffffff]
[    0.083411] pci 0000:01:00.0: reg 14 32bit mmio: [0xcfee0000-0xcfefffff]
[    0.083422] pci 0000:01:00.0: reg 18 io port: [0xac00-0xac7f]
[    0.083471] pci 0000:01:00.0: supports D1 D2
[    0.083529] pci 0000:00:01.0: bridge io port: [0xa000-0xafff]
[    0.083538] pci 0000:00:01.0: bridge 32bit mmio: [0xcfd00000-0xcfefffff]
[    0.083547] pci 0000:00:01.0: bridge 32bit mmio pref: [0xbfa00000-0xcfbfffff]
[    0.083561] pci_bus 0000:00: on NUMA node 0
[    0.083569] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
[    0.086652] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 7 10 *11 12 14 15)
[    0.086871] ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 *5 7 10 11 12 14 15)
[    0.087083] ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 7 *10 11 12 14 15)
[    0.087292] ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 7 10 11 12 14 15) *0, disabled.
[    0.087502] ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 7 *10 11 12 14 15)
[    0.087711] ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 *5 7 10 11 12 14 15)
[    0.087920] ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 7 10 11 12 14 15) *0, disabled.
[    0.088158] ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 *5 7 10 11 12 14 15)
[    0.088446] vgaarb: device added: PCI:0000:01:00.0,decodes=io+mem,owns=io+mem,locks=none
[    0.088452] vgaarb: loaded
[    0.088779] SCSI subsystem initialized
[    0.089033] libata version 3.00 loaded.
[    0.089220] usbcore: registered new interface driver usbfs
[    0.089247] usbcore: registered new interface driver hub
[    0.089313] usbcore: registered new device driver usb
[    0.089624] ACPI: WMI: Mapper loaded
[    0.089628] PCI: Using ACPI for IRQ routing
[    0.089993] NetLabel: Initializing
[    0.089998] NetLabel:  domain hash size = 128
[    0.090001] NetLabel:  protocols = UNLABELED CIPSOv4
[    0.090042] NetLabel:  unlabeled traffic allowed by default
[    0.090123] Switching to clocksource tsc
[    0.092861] AppArmor: AppArmor Filesystem Enabled
[    0.092940] pnp: PnP ACPI init
[    0.093001] ACPI: bus type pnp registered
[    0.099113] pnp: PnP ACPI: found 9 devices
[    0.099119] ACPI: ACPI bus type pnp unregistered
[    0.099128] PnPBIOS: Disabled by ACPI PNP
[    0.099164] system 00:01: ioport range 0x290-0x297 has been reserved
[    0.099171] system 00:01: ioport range 0x480-0x48f has been reserved
[    0.099176] system 00:01: ioport range 0x4d0-0x4d1 has been reserved
[    0.099182] system 00:01: ioport range 0x820-0x821 has been reserved
[    0.099188] system 00:01: ioport range 0x862-0x862 has been reserved
[    0.099194] system 00:01: ioport range 0x866-0x8ff has been reserved
[    0.099200] system 00:01: ioport range 0xc00-0xc1f has been reserved
[    0.099205] system 00:01: ioport range 0x3f0-0x3f1 has been reserved
[    0.134175] pci 0000:00:01.0: PCI bridge, secondary bus 0000:01
[    0.134183] pci 0000:00:01.0:   IO window: 0xa000-0xafff
[    0.134196] pci 0000:00:01.0:   MEM window: 0xcfd00000-0xcfefffff
[    0.134205] pci 0000:00:01.0:   PREFETCH window: 0xbfa00000-0xcfbfffff
[    0.134239] pci_bus 0000:00: resource 0 io:  [0x00-0xffff]
[    0.134245] pci_bus 0000:00: resource 1 mem: [0x000000-0xffffffff]
[    0.134251] pci_bus 0000:01: resource 0 io:  [0xa000-0xafff]
[    0.134257] pci_bus 0000:01: resource 1 mem: [0xcfd00000-0xcfefffff]
[    0.134262] pci_bus 0000:01: resource 2 pref mem [0xbfa00000-0xcfbfffff]
[    0.134360] NET: Registered protocol family 2
[    0.134560] IP route cache hash table entries: 2048 (order: 1, 8192 bytes)
[    0.135130] TCP established hash table entries: 8192 (order: 4, 65536 bytes)
[    0.135354] TCP bind hash table entries: 8192 (order: 4, 65536 bytes)
[    0.135571] TCP: Hash tables configured (established 8192 bind 8192)
[    0.135576] TCP reno registered
[    0.135722] NET: Registered protocol family 1
[    0.173820] pci 0000:01:00.0: Boot video device
[    0.174320] cpufreq-nforce2: No nForce2 chipset.
[    0.174376] Scanning for low memory corruption every 60 seconds
[    0.174645] audit: initializing netlink socket (disabled)
[    0.174675] type=2000 audit(1282692035.173:1): initialized
[    0.191554] Trying to unpack rootfs image as initramfs...
[    0.210875] HugeTLB registered 4 MB page size, pre-allocated 0 pages
[    0.217946] VFS: Disk quotas dquot_6.5.2
[    0.218210] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[    0.219555] fuse init (API version 7.13)
[    0.219742] msgmni has been set to 399
[    0.226245] alg: No test for stdrng (krng)
[    0.226470] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253)
[    0.226478] io scheduler noop registered
[    0.226482] io scheduler anticipatory registered
[    0.226486] io scheduler deadline registered

[jeffersonsan]

Código Selecionar Expandir

[    0.226592] io scheduler cfq registered (default)
[    0.226863] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[    0.226912] pciehp: PCI Express Hot Plug Controller Driver version: 0.4
[    0.228030] ACPI: AC Adapter [AC] (on-line)
[    0.228254] input: Power Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0C:00/input/input0
[    0.228266] ACPI: Power Button [PWRB]
[    0.228360] input: Lid Switch as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0D:00/input/input1
[    0.228463] ACPI: Lid Switch [LID0]
[    0.228575] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input2
[    0.228582] ACPI: Power Button [PWRF]
[    0.228872] processor LNXCPU:00: registered as cooling_device0
[    0.269500] isapnp: Scanning for PnP cards...
[    0.275604] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
[    0.346963] ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 10
[    0.346977] PCI: setting IRQ 10 as level-triggered
[    0.346989] serial 0000:00:02.6: PCI INT C -> Link[LNKC] -> GSI 10 (level, low) -> IRQ 10
[    0.347016] serial 0000:00:02.6: PCI INT C disabled
[    0.349557] brd: module loaded
[    0.353631] loop: module loaded
[    0.353966] input: Macintosh mouse button emulation as /devices/virtual/input/input3
[    0.354321] pata_sis 0000:00:02.5: version 0.5.2
[    0.357994] scsi0 : pata_sis
[    0.358397] scsi1 : pata_sis
[    0.360031] ata1: PATA max UDMA/133 cmd 0x1f0 ctl 0x3f6 bmdma 0xff00 irq 14
[    0.360039] ata2: PATA max UDMA/133 cmd 0x170 ctl 0x376 bmdma 0xff08 irq 15
[    0.360842] Fixed MDIO Bus: probed
[    0.360922] PPP generic driver version 2.4.2
[    0.361132] tun: Universal TUN/TAP device driver, 1.6
[    0.361137] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
[    0.361372] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    0.361843] ACPI: PCI Interrupt Link [LNKH] enabled at IRQ 5
[    0.361849] PCI: setting IRQ 5 as level-triggered
[    0.361859] ehci_hcd 0000:00:03.3: PCI INT D -> Link[LNKH] -> GSI 5 (level, low) -> IRQ 5
[    0.366288] ehci_hcd 0000:00:03.3: EHCI Host Controller
[    0.366582] ehci_hcd 0000:00:03.3: new USB bus registered, assigned bus number 1
[    0.366672] ehci_hcd 0000:00:03.3: cache line size of 64 is not supported
[    0.366701] ehci_hcd 0000:00:03.3: irq 5, io mem 0xcfffb000
[    0.377900] ehci_hcd 0000:00:03.3: USB 2.0 started, EHCI 1.00
[    0.378310] usb usb1: configuration #1 chosen from 1 choice
[    0.378387] hub 1-0:1.0: USB hub found
[    0.378424] hub 1-0:1.0: 6 ports detected
[    0.378578] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[    0.379110] ACPI: PCI Interrupt Link [LNKE] enabled at IRQ 10
[    0.379120] ohci_hcd 0000:00:03.0: PCI INT A -> Link[LNKE] -> GSI 10 (level, low) -> IRQ 10
[    0.379167] ohci_hcd 0000:00:03.0: OHCI Host Controller
[    0.379292] ohci_hcd 0000:00:03.0: new USB bus registered, assigned bus number 2
[    0.379349] ohci_hcd 0000:00:03.0: irq 10, io mem 0xcfff9000
[    0.436373] usb usb2: configuration #1 chosen from 1 choice
[    0.436451] hub 2-0:1.0: USB hub found
[    0.436488] hub 2-0:1.0: 3 ports detected
[    0.437120] ACPI: PCI Interrupt Link [LNKF] enabled at IRQ 5
[    0.437131] ohci_hcd 0000:00:03.1: PCI INT B -> Link[LNKF] -> GSI 5 (level, low) -> IRQ 5
[    0.437178] ohci_hcd 0000:00:03.1: OHCI Host Controller
[    0.437299] ohci_hcd 0000:00:03.1: new USB bus registered, assigned bus number 3
[    0.437355] ohci_hcd 0000:00:03.1: irq 5, io mem 0xcfffa000
[    0.520144] usb usb3: configuration #1 chosen from 1 choice
[    0.520225] hub 3-0:1.0: USB hub found
[    0.520263] hub 3-0:1.0: 3 ports detected
[    0.520427] uhci_hcd: USB Universal Host Controller Interface driver
[    0.520662] PNP: PS/2 Controller [PNP0303:PS2K,PNP0f03:PS2M] at 0x60,0x64 irq 1,12
[    0.546226] i8042.c: Detected active multiplexing controller, rev 1.1.
[    0.546508] serio: i8042 KBD port at 0x60,0x64 irq 1
[    0.546532] serio: i8042 AUX0 port at 0x60,0x64 irq 12
[    0.546663] serio: i8042 AUX1 port at 0x60,0x64 irq 12
[    0.546713] serio: i8042 AUX2 port at 0x60,0x64 irq 12
[    0.546774] serio: i8042 AUX3 port at 0x60,0x64 irq 12
[    0.547167] mice: PS/2 mouse device common for all mice
[    0.547504] rtc_cmos 00:03: RTC can wake from S4
[    0.547624] rtc_cmos 00:03: rtc core: registered rtc_cmos as rtc0
[    0.547659] rtc0: alarms up to one month, 114 bytes nvram
[    0.547888] device-mapper: uevent: version 1.0.3
[    0.551090] device-mapper: ioctl: 4.15.0-ioctl (2009-04-01) initialised: dm-devel@redhat.com
[    0.553290] input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input4
[    0.553568] device-mapper: multipath: version 1.1.0 loaded
[    0.553577] device-mapper: multipath round-robin: version 1.0.0 loaded
[    0.554213] EISA: Probing bus 0 at eisa.0
[    0.554267] EISA: Detected 0 cards.
[    0.557126] cpuidle: using governor ladder
[    0.557136] cpuidle: using governor menu
[    0.558209] TCP cubic registered
[    0.558535] NET: Registered protocol family 10
[    0.559431] lo: Disabled Privacy Extensions
[    0.560025] NET: Registered protocol family 17
[    0.560132] powernow-k8: Processor cpuid 662 not supported
[    0.560283] powernow: PowerNOW! Technology present. Can scale: frequency and voltage.
[    0.582295] powernow: SGTC: 10000
[    0.582305] powernow: Minimum speed 796 MHz. Maximum speed 1194 MHz.
[    0.582466] Using IPI No-Shortcut mode
[    0.582785] PM: Resume from disk failed.
[    0.582825] registered taskstats version 1
[    0.583202]   Magic number: 6:528:353
[    0.583459] rtc_cmos 00:03: setting system clock to 2010-08-24 23:20:36 UTC (1282692036)
[    0.583468] BIOS EDD facility v0.16 2004-Jun-25, 0 devices found
[    0.583471] EDD information not available.
[    0.583773] ata1.00: ATA-5: HITACHI_DK23FB-40, 00M1A0A1, max UDMA/100
[    0.583779] ata1.00: 78140160 sectors, multi 16: LBA
[    0.583823] ata1.00: limited to UDMA/33 due to 40-wire cable
[    0.590350] ata1.00: configured for UDMA/33
[    0.770685] ACPI: Battery Slot [BAT0] (battery present)
[    1.001948] isapnp: No Plug & Play device found
[    1.002437] scsi 0:0:0:0: Direct-Access     ATA      HITACHI_DK23FB-4 00M1 PQ: 0 ANSI: 5
[    1.002906] sd 0:0:0:0: Attached scsi generic sg0 type 0
[    1.003294] sd 0:0:0:0: [sda] 78140160 512-byte logical blocks: (40.0 GB/37.2 GiB)
[    1.003421] sd 0:0:0:0: [sda] Write Protect is off
[    1.003427] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[    1.003491] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[    1.003861]  sda: sda1 sda2 sda3
[    1.040686] sd 0:0:0:0: [sda] Attached SCSI disk
[    1.132595] ata2.00: ATAPI: UJDA760 DVD/CDRW, 1.01, max UDMA/33
[    1.148775] ata2.00: configured for UDMA/33
[    1.151002] scsi 1:0:0:0: CD-ROM            MATSHITA UJDA760 DVD/CDRW 1.01 PQ: 0 ANSI: 5
[    1.152771] usb 3-2: new full speed USB device using ohci_hcd and address 2
[    1.152843] sr0: scsi3-mmc drive: 24x/24x writer cd/rw xa/form2 cdda tray
[    1.152852] Uniform CD-ROM driver Revision: 3.20
[    1.153210] sr 1:0:0:0: Attached scsi CD-ROM sr0
[    1.153389] sr 1:0:0:0: Attached scsi generic sg1 type 5
[    1.336619] usb 3-2: device descriptor read/64, error -62
[    1.385087] Freeing initrd memory: 13067k freed
[    1.423668] Freeing unused kernel memory: 656k freed
[    1.425852] Write protecting the kernel text: 4676k
[    1.425912] Write protecting the kernel read-only data: 1840k
[    1.490446] udev: starting version 151
[    1.620222] usb 3-2: device descriptor read/64, error -62
[    1.908224] usb 3-2: new full speed USB device using ohci_hcd and address 3
[    2.018355] Linux agpgart interface v0.103
[    2.030340] vga16fb: initializing
[    2.030355] vga16fb: mapped to 0xc00a0000
[    2.030547] fb0: VGA16 VGA frame buffer device
[    2.048886] r8169 Gigabit Ethernet driver 2.3LK-NAPI loaded
[    2.049957] ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 5
[    2.049970] r8169 0000:00:07.0: PCI INT A -> Link[LNKB] -> GSI 5 (level, low) -> IRQ 5
[    2.050046] r8169 0000:00:07.0: no PCI Express capability
[    2.051625] eth0: RTL8110s at 0xce87ef00, 00:11:5b:4c:f5:a9, XID 04000000 IRQ 5
[    2.064571] agpgart-sis 0000:00:00.0: SiS chipset [1039/0740]
[    2.073517] agpgart-sis 0000:00:00.0: AGP aperture is 32M @ 0xd0000000
[    2.119383] usb 3-2: device descriptor read/64, error -62
[    2.190439] Console: switching to colour frame buffer device 80x30
[    2.400062] usb 3-2: device descriptor read/64, error -62
[    2.680049] usb 3-2: new full speed USB device using ohci_hcd and address 4
[    3.088093] usb 3-2: device not accepting address 4, error -62
[    3.261555] xor: automatically using best checksumming function: pIII_sse
[    3.280024]    pIII_sse  :  2361.000 MB/sec
[    3.280029] xor: using function: pIII_sse (2361.000 MB/sec)
[    3.280077] usb 3-2: new full speed USB device using ohci_hcd and address 5
[    3.313026] device-mapper: dm-raid45: initialized v0.2594b
[    3.523522] REISERFS (device sda2): found reiserfs format "3.6" with standard journal
[    3.523557] REISERFS (device sda2): using ordered data mode
[    3.546065] REISERFS (device sda2): journal params: device sda2, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30
[    3.549017] REISERFS (device sda2): checking transaction log (sda2)
[    3.586911] REISERFS (device sda2): Using r5 hash to sort names
[    3.688049] usb 3-2: device not accepting address 5, error -62
[    3.688101] hub 3-0:1.0: unable to enumerate USB device on port 2
[    6.795334] Adding 1018872k swap on /dev/sda1.  Priority:-1 extents:1 across:1018872k
[    7.063375] udev: starting version 151
[    7.434315] lp: driver loaded but no devices found
[    7.777405] sis96x_smbus 0000:00:02.1: SiS96x SMBus base address: 0x0c00
[    7.777423] ACPI: resource 0000:00:02.1 [0xc00-0xc1f] conflicts with ACPI region SMRG [0xc00-0xc1f]
[    7.777429] ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver
[    7.778235] parport_pc 00:08: reported by Plug and Play ACPI
[    7.778305] parport0: PC-style at 0x378 (0x778), irq 7, dma 3 [PCSPP,TRISTATE,COMPAT,ECP,DMA]
[    7.829914] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
[    7.868591] lp0: using parport0 (interrupt-driven).
[    8.521642] ppdev: user-space parallel port driver
[    8.614222] Synaptics Touchpad, model: 1, fw: 5.9, id: 0x1d6eb1, caps: 0xa04713/0x4006
[    8.646086] input: SynPS/2 Synaptics TouchPad as /devices/platform/i8042/serio4/input/input5
[    8.960671] type=1505 audit(1282692044.876:2):  operation="profile_load" pid=491 name="/sbin/dhclient3"
[    8.961279] type=1505 audit(1282692044.876:3):  operation="profile_load" pid=491 name="/usr/lib/NetworkManager/nm-dhcp-client.action"


[jeffersonsan]

Código Selecionar Expandir

[    8.961626] type=1505 audit(1282692044.876:4):  operation="profile_load" pid=491 name="/usr/lib/connman/scripts/dhclient-script"
[    9.096172] type=1505 audit(1282692045.012:5):  operation="profile_load" pid=537 name="/usr/sbin/ntpd"
[    9.108855] REISERFS (device sda3): found reiserfs format "3.6" with standard journal
[    9.108901] REISERFS (device sda3): using ordered data mode
[    9.134627] REISERFS (device sda3): journal params: device sda3, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30
[    9.137646] REISERFS (device sda3): checking transaction log (sda3)
[    9.210615] REISERFS (device sda3): Using r5 hash to sort names
[    9.547317] Intel ICH 0000:00:02.7: PCI INT C -> Link[LNKC] -> GSI 10 (level, low) -> IRQ 10
[   10.372066] intel8x0_measure_ac97_clock: measured 55121 usecs (2652 samples)
[   10.372078] intel8x0: clocking to 48000
[   10.800706] type=1505 audit(1282692046.716:6):  operation="profile_replace" pid=631 name="/sbin/dhclient3"
[   10.801369] type=1505 audit(1282692046.716:7):  operation="profile_replace" pid=631 name="/usr/lib/NetworkManager/nm-dhcp-client.action"
[   10.801736] type=1505 audit(1282692046.716:8):  operation="profile_replace" pid=631 name="/usr/lib/connman/scripts/dhclient-script"
[   10.887627] type=1505 audit(1282692046.800:9):  operation="profile_load" pid=632 name="/usr/lib/cups/backend/cups-pdf"
[   10.889111] type=1505 audit(1282692046.804:10):  operation="profile_load" pid=632 name="/usr/sbin/cupsd"
[   10.907081] type=1505 audit(1282692046.820:11):  operation="profile_replace" pid=636 name="/usr/sbin/ntpd"
[   12.109217] r8169: eth0: link up
[   22.804068] eth0: no IPv6 routers present
[   74.624323] Marking TSC unstable due to cpufreq changes
[   74.627192] Switching to clocksource acpi_pm
[  689.928156] usb 3-2: new full speed USB device using ohci_hcd and address 6
[  690.112113] usb 3-2: device descriptor read/64, error -62
[  690.396172] usb 3-2: device descriptor read/64, error -62
[  690.676193] usb 3-2: new full speed USB device using ohci_hcd and address 7
[  690.860143] usb 3-2: device descriptor read/64, error -62
[  691.148156] usb 3-2: device descriptor read/64, error -62
[  691.428175] usb 3-2: new full speed USB device using ohci_hcd and address 8
[  691.541440] ISO 9660 Extensions: Microsoft Joliet Level 3
[  691.561397] ISO 9660 Extensions: RRIP_1991A
[  691.836091] usb 3-2: device not accepting address 8, error -62
[  692.012246] usb 3-2: new full speed USB device using ohci_hcd and address 9
[  692.420089] usb 3-2: device not accepting address 9, error -62
[  692.420141] hub 3-0:1.0: unable to enumerate USB device on port 2
[  697.146461] sr 1:0:0:0: [sr0] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE
[  697.146483] sr 1:0:0:0: [sr0] Sense Key : Illegal Request [current]
[  697.146498] ILI
[  697.146503] sr 1:0:0:0: [sr0] Add. Sense: Illegal mode for this track
[  697.146532] sr 1:0:0:0: [sr0] CDB: Read(10): 28 00 00 04 11 f6 00 00 01 00
[  697.146559] end_request: I/O error, dev sr0, sector 1066968
[  697.146577] __ratelimit: 3 callbacks suppressed
[  697.146586] Buffer I/O error on device sr0, logical block 266742
[  697.450790] sr 1:0:0:0: [sr0] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE
[  697.450811] sr 1:0:0:0: [sr0] Sense Key : Illegal Request [current]
[  697.450826] ILI
[  697.450831] sr 1:0:0:0: [sr0] Add. Sense: Illegal mode for this track
[  697.450859] sr 1:0:0:0: [sr0] CDB: Read(10): 28 00 00 04 11 f6 00 00 01 00
[  697.450886] end_request: I/O error, dev sr0, sector 1066968
[  697.450905] Buffer I/O error on device sr0, logical block 266742
[  697.743753] sr 1:0:0:0: [sr0] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE
[  697.743777] sr 1:0:0:0: [sr0] Sense Key : Illegal Request [current]
[  697.743791] ILI
[  697.743796] sr 1:0:0:0: [sr0] Add. Sense: Illegal mode for this track
[  697.743823] sr 1:0:0:0: [sr0] CDB: Read(10): 28 00 00 04 11 f6 00 00 01 00
[  697.743850] end_request: I/O error, dev sr0, sector 1066968
[  697.743870] Buffer I/O error on device sr0, logical block 266742
[  698.032326] sr 1:0:0:0: [sr0] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE
[  698.032348] sr 1:0:0:0: [sr0] Sense Key : Illegal Request [current]
[  698.032362] ILI
[  698.032368] sr 1:0:0:0: [sr0] Add. Sense: Illegal mode for this track
[  698.032395] sr 1:0:0:0: [sr0] CDB: Read(10): 28 00 00 04 11 f6 00 00 01 00
[  698.032424] end_request: I/O error, dev sr0, sector 1066968
[  698.032442] Buffer I/O error on device sr0, logical block 266742
[  698.318861] sr 1:0:0:0: [sr0] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE
[  698.318883] sr 1:0:0:0: [sr0] Sense Key : Illegal Request [current]
[  698.318898] ILI
[  698.318904] sr 1:0:0:0: [sr0] Add. Sense: Illegal mode for this track
[  698.318931] sr 1:0:0:0: [sr0] CDB: Read(10): 28 00 00 04 11 f6 00 00 01 00
[  698.318958] end_request: I/O error, dev sr0, sector 1066968
[  698.318978] Buffer I/O error on device sr0, logical block 266742
[  698.605891] sr 1:0:0:0: [sr0] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE
[  698.605912] sr 1:0:0:0: [sr0] Sense Key : Illegal Request [current]
[  698.605927] ILI
[  698.605932] sr 1:0:0:0: [sr0] Add. Sense: Illegal mode for this track
[  698.605960] sr 1:0:0:0: [sr0] CDB: Read(10): 28 00 00 04 11 f6 00 00 01 00
[  698.605987] end_request: I/O error, dev sr0, sector 1066968
[  698.606007] Buffer I/O error on device sr0, logical block 266742
[  698.892780] sr 1:0:0:0: [sr0] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE
[  698.892802] sr 1:0:0:0: [sr0] Sense Key : Illegal Request [current]
[  698.892817] ILI
[  698.892822] sr 1:0:0:0: [sr0] Add. Sense: Illegal mode for this track
[  698.892850] sr 1:0:0:0: [sr0] CDB: Read(10): 28 00 00 04 11 f6 00 00 01 00
[  698.892877] end_request: I/O error, dev sr0, sector 1066968
[  698.892897] Buffer I/O error on device sr0, logical block 266742
[  699.251751] sr 1:0:0:0: [sr0] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE
[  699.251773] sr 1:0:0:0: [sr0] Sense Key : Illegal Request [current]
[  699.251787] ILI
[  699.251792] sr 1:0:0:0: [sr0] Add. Sense: Illegal mode for this track
[  699.251832] sr 1:0:0:0: [sr0] CDB: Read(10): 28 00 00 04 11 f6 00 00 01 00
[  699.251859] end_request: I/O error, dev sr0, sector 1066968
[  699.251878] Buffer I/O error on device sr0, logical block 266742
[  699.539343] sr 1:0:0:0: [sr0] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE
[  699.539366] sr 1:0:0:0: [sr0] Sense Key : Illegal Request [current]
[  699.539382] ILI
[  699.539387] sr 1:0:0:0: [sr0] Add. Sense: Illegal mode for this track
[  699.539416] sr 1:0:0:0: [sr0] CDB: Read(10): 28 00 00 04 11 f6 00 00 01 00
[  699.539444] end_request: I/O error, dev sr0, sector 1066968
[  699.539462] Buffer I/O error on device sr0, logical block 266742
[  699.827040] sr 1:0:0:0: [sr0] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE
[  699.827062] sr 1:0:0:0: [sr0] Sense Key : Illegal Request [current]
[  699.827077] ILI
[  699.827082] sr 1:0:0:0: [sr0] Add. Sense: Illegal mode for this track
[  699.827112] sr 1:0:0:0: [sr0] CDB: Read(10): 28 00 00 04 11 f6 00 00 01 00
[  699.827138] end_request: I/O error, dev sr0, sector 1066968
[  699.827156] Buffer I/O error on device sr0, logical block 266742
[  700.835541] sr 1:0:0:0: [sr0] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE
[  700.835564] sr 1:0:0:0: [sr0] Sense Key : Illegal Request [current]
[  700.835579] ILI
[  700.835584] sr 1:0:0:0: [sr0] Add. Sense: Illegal mode for this track
[  700.835613] sr 1:0:0:0: [sr0] CDB: Read(10): 28 00 00 04 11 f6 00 00 01 00
[  700.835641] end_request: I/O error, dev sr0, sector 1066968
[  701.123994] sr 1:0:0:0: [sr0] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE
[  701.124066] sr 1:0:0:0: [sr0] Sense Key : Illegal Request [current]
[  701.124081] ILI
[  701.124087] sr 1:0:0:0: [sr0] Add. Sense: Illegal mode for this track
[  701.124115] sr 1:0:0:0: [sr0] CDB: Read(10): 28 00 00 04 11 f6 00 00 01 00
[  701.124142] end_request: I/O error, dev sr0, sector 1066968
[  701.411420] sr 1:0:0:0: [sr0] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE
[  701.411442] sr 1:0:0:0: [sr0] Sense Key : Illegal Request [current]
[  701.411457] ILI
[  701.411462] sr 1:0:0:0: [sr0] Add. Sense: Illegal mode for this track
[  701.411491] sr 1:0:0:0: [sr0] CDB: Read(10): 28 00 00 04 11 f6 00 00 01 00
[  701.411518] end_request: I/O error, dev sr0, sector 1066968
[  701.701642] sr 1:0:0:0: [sr0] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE
[  701.701665] sr 1:0:0:0: [sr0] Sense Key : Illegal Request [current]
[  701.701681] ILI
[  701.701686] sr 1:0:0:0: [sr0] Add. Sense: Illegal mode for this track
[  701.701714] sr 1:0:0:0: [sr0] CDB: Read(10): 28 00 00 04 11 f6 00 00 01 00
[  701.701741] end_request: I/O error, dev sr0, sector 1066968
[  701.990726] sr 1:0:0:0: [sr0] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE
[  701.990747] sr 1:0:0:0: [sr0] Sense Key : Illegal Request [current]
[  701.990762] ILI
[  701.990767] sr 1:0:0:0: [sr0] Add. Sense: Illegal mode for this track
[  701.990796] sr 1:0:0:0: [sr0] CDB: Read(10): 28 00 00 04 11 f6 00 00 01 00
[  701.990823] end_request: I/O error, dev sr0, sector 1066968
[  702.277980] sr 1:0:0:0: [sr0] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE
[  702.278000] sr 1:0:0:0: [sr0] Sense Key : Illegal Request [current]
[  702.278015] ILI
[  702.278020] sr 1:0:0:0: [sr0] Add. Sense: Illegal mode for this track
[  702.278048] sr 1:0:0:0: [sr0] CDB: Read(10): 28 00 00 04 11 f6 00 00 01 00
[  702.278075] end_request: I/O error, dev sr0, sector 1066968
[  702.569246] sr 1:0:0:0: [sr0] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE
[  702.569268] sr 1:0:0:0: [sr0] Sense Key : Illegal Request [current]
[  702.569284] ILI
[  702.569289] sr 1:0:0:0: [sr0] Add. Sense: Illegal mode for this track
[  702.569317] sr 1:0:0:0: [sr0] CDB: Read(10): 28 00 00 04 11 f6 00 00 01 00
[  702.569345] end_request: I/O error, dev sr0, sector 1066968
[  702.569363] __ratelimit: 6 callbacks suppressed
[  702.569375] Buffer I/O error on device sr0, logical block 266742
[  702.857148] sr 1:0:0:0: [sr0] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE
[  702.857171] sr 1:0:0:0: [sr0] Sense Key : Illegal Request [current]
[  702.857185] ILI
[  702.857191] sr 1:0:0:0: [sr0] Add. Sense: Illegal mode for this track
[  702.857219] sr 1:0:0:0: [sr0] CDB: Read(10): 28 00 00 04 11 f6 00 00 01 00
[  702.857247] end_request: I/O error, dev sr0, sector 1066968
[  702.857268] Buffer I/O error on device sr0, logical block 266742
[  703.148644] sr 1:0:0:0: [sr0] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE
[  703.148666] sr 1:0:0:0: [sr0] Sense Key : Illegal Request [current]
[  703.148680] ILI
[  703.148683] sr 1:0:0:0: [sr0] Add. Sense: Illegal mode for this track
[  703.148713] sr 1:0:0:0: [sr0] CDB: Read(10): 28 00 00 04 11 f6 00 00 01 00
[  703.148734] end_request: I/O error, dev sr0, sector 1066968
[  703.148755] Buffer I/O error on device sr0, logical block 266742
[  816.172089] usb 3-2: new full speed USB device using ohci_hcd and address 10
[  816.356111] usb 3-2: device descriptor read/64, error -62
[  816.644130] usb 3-2: device descriptor read/64, error -62
[  816.924173] usb 3-2: new full speed USB device using ohci_hcd and address 11
[  817.108161] usb 3-2: device descriptor read/64, error -62
[  817.392075] usb 3-2: device descriptor read/64, error -62
[  817.672134] usb 3-2: new full speed USB device using ohci_hcd and address 12
[  818.080112] usb 3-2: device not accepting address 12, error -62
[  818.256151] usb 3-2: new full speed USB device using ohci_hcd and address 13
[  818.664116] usb 3-2: device not accepting address 13, error -62
[  818.664189] hub 3-0:1.0: unable to enumerate USB device on port 2
[ 1030.288130] usb 3-2: new full speed USB device using ohci_hcd and address 14
[ 1030.472087] usb 3-2: device descriptor read/64, error -62
[ 1030.760068] usb 3-2: device descriptor read/64, error -62
[ 1031.040108] usb 3-2: new full speed USB device using ohci_hcd and address 15
[ 1031.224104] usb 3-2: device descriptor read/64, error -62
[ 1031.508151] usb 3-2: device descriptor read/64, error -62
[ 1031.788096] usb 3-2: new full speed USB device using ohci_hcd and address 16
[ 1032.196085] usb 3-2: device not accepting address 16, error -62
[ 1032.372087] usb 3-2: new full speed USB device using ohci_hcd and address 17
[ 1032.780079] usb 3-2: device not accepting address 17, error -62
[ 1032.780150] hub 3-0:1.0: unable to enumerate USB device on port 2
[ 6617.238138] psmouse.c: TouchPad at isa0060/serio4/input0 lost sync at byte 1
[ 6617.238176] psmouse.c: TouchPad at isa0060/serio4/input0 lost sync at byte 1
[ 6663.280740] psmouse.c: TouchPad at isa0060/serio4/input0 - driver resynched.

[jeffersonsan]

e no lsmod

Código Selecionar Expandir

Module                  Size  Used by
nls_utf8                1069  1
isofs                  29250  1
dm_crypt               11331  0
snd_intel8x0           25588  1
snd_ac97_codec        100646  1 snd_intel8x0
ac97_bus                1002  1 snd_ac97_codec
snd_pcm_oss            35308  0
snd_mixer_oss          13746  1 snd_pcm_oss
snd_pcm                70662  3 snd_intel8x0,snd_ac97_codec,snd_pcm_oss
snd_seq_dummy           1338  0
snd_seq_oss            26726  0
snd_seq_midi            4557  0
snd_rawmidi            19056  1 snd_seq_midi
snd_seq_midi_event      6003  2 snd_seq_oss,snd_seq_midi
snd_seq                47263  6 snd_seq_dummy,snd_seq_oss,snd_seq_midi,snd_seq_midi_event
joydev                  8708  0
snd_timer              19098  2 snd_pcm,snd_seq
snd_seq_device          5700  5 snd_seq_dummy,snd_seq_oss,snd_seq_midi,snd_rawmidi,snd_seq
ppdev                   5259  0
snd                    54148  12 snd_intel8x0,snd_ac97_codec,snd_pcm_oss,snd_mixer_oss,snd_pcm,snd_seq_oss,snd_rawmidi,snd_seq,snd_timer,snd_seq_device
psmouse                63245  0
soundcore               6620  1 snd
snd_page_alloc          7076  2 snd_intel8x0,snd_pcm
serio_raw               3978  0
shpchp                 28820  0
i2c_sis96x              3024  0
parport_pc             25962  1
lp                      7028  0
parport                32635  3 ppdev,parport_pc,lp
reiserfs              225633  2
dm_raid45              81647  0
xor                    15028  1 dm_raid45
fbcon                  35102  71
tileblit                2031  1 fbcon
font                    7557  1 fbcon
bitblit                 4707  1 fbcon
softcursor              1189  1 bitblit
sis_agp                 4047  1
r8169                  33884  0
mii                     4381  1 r8169
vga16fb                11385  1
vgastate                8961  1 vga16fb
agpgart                31724  1 sis_agp

Um abraço

[zekkerj]

Oi jefferson. Posso te dar uma sugestão? Eu acho que não vale muito a pena investir nessa placa... além de vc estar apanhando dela --- e ela nem foi reconhecida no lsusb! ---, ela é 802.11b, ou seja, além de ser limitada a 11Mbps, na hora em que vc a estiver usando, ela vai fazer todos os outros dispositivos no alcance ficarem limitados a 11Mbps também, mesmo que sejam capazes de trabalhar a 300Mbps.

Além disso, seu notebook é antigo, não? Vc não disse se essa placa estava funcionando antes de instalar o Linux nele. Estava?

Então, uma boa idéia seria você pegar um adaptador wireless USB, e tentar a vida com ele. Vc vai conseguir alguns a preços razoáveis.

Note que não estou dizendo que seja impossível... só acho que o resultado não vale o trabalho que você está tendo.

[Tota]

Bom,

Como bem disse o zekkrj, ela não está habilitada.

Pelo lsmod ( que mostra os modulos instalados ) o prism2-usb não foi "levantado"

Acredito que voce já deve ter visto isto => http://wiki.debian.org/linux-wlan-ng

Li por alto, e como voce já instalou os modulos e o firmware, pode tentar em terminal

Código Selecionar Expandir

sudo modprobe prism2-usb

e ver se o modulo é "levantado", ou seja, se é carregado.

E também como disse o zekkrj é uma placa meio antiga, e que não suporta encriptação avançada ( WPA ) logo sua rede vai ficar sempre insegura.

[]'s

[jeffersonsan]

Boa tarde.
A placa funcionava, com Windows. Anteontem a instalei com o Vector Linux (usando ndiswrapper e modprobe)e a luz até acendeu, (o linux reconheceu que existia a placa) mas não consegui conexão. Pensei que com o Lubuntu seria mais fácil.
O problema é que apaguei o arquivo .inf e o .sys que, talvez funcionasse.
Mudar a placa é minha ultimíssima opção (não estou querendo gastar muito com esta máquina, mas se não tiver jeito...), além do mais, minha conexão atual é lenta (560kbps), acho que tão cedo não vou fazer upgrade.
Agora, pensando em usar o ndiswrapper no lubuntu...
Baixei o pacote de driver da placa no site da ECS. Descompactei e fiz o ndiswrapper com o arquivo .inf que apareceu lá(AVWLPNIC.inf e AVWLPNIC.sys). Também nao surtiu efeito. Agora pergunto:
É possível fazer com que o linux extraia o pacote de driver como se estivesse no Windows? Explico. Na pasta de drivers que tinha do Windows, para a placa wireless havia um arquivo chamado "oem7.inf" e "oem7. sys" (foi com eles que consegui que acendesse a luz sob o Vector Linux), será que consigo compilá-los com o pacote de driver que baixei sem ter que instalar o Windows e depois o Lubuntu?
Ah.. e pra adiantar, e pra não ficar novamente batendo cabeça caso não encontre solução, qual adaptador usb wireless vocês me recomendariam (que atenda ao famoso bb [bom, ou funcional, e barato])?

Abraços e mais uma vez obrigado.

[Tota]

Se tem o cd do windows em mãos basta extrair estes dois arquivos que estão dentro do cd.

Geralmente estariam assim=> oem7. sy_

Indicando estarem compactados. Use o comando extract para obter o arquivo.

Vá até uma maquina que possua o windows instalado ( vizinho as vezes serve para alguma coisa    ) e faça o procedimento gravando num pen drive por exemplo.

[jeffersonsan]

Desisti...

Me debati muito, tentei de tudo que fiquei sabendo e nada... O laptop é muito antigo, não vale investir em equipamento. Coloquei o windows xp nele novamente e a placa está funcionando belezinha.

Obrigado aos amigos que tentaram ajudar.

Minha avó sempre diz: Se não tem remédio, remediado está.
Abraços!