erro no lm-sensors

[joefreire]

ola galera eu instalei o sensors normal
so q deu esse resultado

Código: [Selecionar]

#----cut here----
# I2C adapter drivers
# modprobe unknown adapter NVIDIA I2C Device
# modprobe unknown adapter NVIDIA I2C Device
# modprobe unknown adapter NVIDIA I2C Device
i2c-isa
# I2C chip drivers
# no driver for Smart Battery Charger yet
# Warning: the required module smartbatt is not currently installed on your system.
# For status of 2.6 kernel ports see http://secure.netroedge.com/~lm78/supported.html
# If driver is built-in to the kernel, or unavailable, comment out the following line.
smartbatt
# Warning: the required module smbus-arp is not currently installed on your system.
# For status of 2.6 kernel ports see http://secure.netroedge.com/~lm78/supported.html
# If driver is built-in to the kernel, or unavailable, comment out the following line.
smbus-arp
eeprom
it87
#----cut here----

ai eu rodei o sensors
deu isso

Can't access procfs/sysfs file
Unable to find i2c bus information;
For 2.6 kernels, make sure you have mounted sysfs and libsensors
was compiled with sysfs support!
For older kernels, make sure you have done 'modprobe i2c-proc'!

alguem pode me ajudar?

[leandrovargas]

joefreire, edit o arquivo /etc/modules e adicione as seguintes linhas (Faça um backup dele antes ) :

Código: [Selecionar]

i2c-isa
smartbatt
smbus-arp
eeprom
it87

Reinicie  o X e rode o sensors, que vai funcionar...Qualquer dúvida retorne aqui..

Vlw

[joefreire]

agora ta dando isso

Can't access procfs/sysfs file
Unable to find i2c bus information;
For 2.6 kernels, make sure you have mounted sysfs and libsensors
was compiled with sysfs support!
For older kernels, make sure you have done 'modprobe i2c-proc'!

Código: [Selecionar]

# /etc/modules: kernel modules to load at boot time.
#
# This file contains the names of kernel modules that should be loaded
# at boot time, one per line. Lines beginning with "#" are ignored.

lp

# Generated by sensors-detect on Sat Feb 10 00:29:56 2007
# I2C adapter drivers
# modprobe unknown adapter NVIDIA I2C Device
# modprobe unknown adapter NVIDIA I2C Device
# modprobe unknown adapter NVIDIA I2C Device
i2c-isa
# I2C chip drivers
# no driver for Smart Battery Charger yet
# Warning: the required module smartbatt is not currently installed on your system.
# For status of 2.6 kernel ports see http://secure.netroedge.com/~lm78/supported.html
# If driver is built-in to the kernel, or unavailable, comment out the following line.
smartbatt
# Warning: the required module smbus-arp is not currently installed on your system.
# For status of 2.6 kernel ports see http://secure.netroedge.com/~lm78/supported.html
# If driver is built-in to the kernel, or unavailable, comment out the following line.
smbus-arp
eeprom
it87


meu modules ta ae

[leandrovargas]

joefreire, rode de novo o sudo sensors-detect, faça tudo de novo, só digite NO, quando ele fizer essa pergunta "Do you want to add these lines to /etc/modules automatically? (yes/NO)" , pois você já adicionou as entradas manualmente no arquivo /etc/modules. Depois digite:

Código: [Selecionar]

sudo modprobe i2c-isa

Código: [Selecionar]

sudo modprobe smartbatt

Código: [Selecionar]

sudo modprobe smbus-arp

Código: [Selecionar]

sudo modprobe eeprom

Código: [Selecionar]

sudo modprobe it87
E rode sensors, que vai funcionar...Qualquer coisa retorne aqui...

Vlw

[joefreire]

guilherme@Guilherme:~$ sudo modprobe smartbatt
FATAL: Module smartbatt not found
guilherme@Guilherme:~$ sudo modprobe smbus-arp
FATAL: Module smbus_arp not found.


guilherme@Guilherme:~$ sensors
Can't access procfs/sysfs file
Unable to find i2c bus information;
For 2.6 kernels, make sure you have mounted sysfs and libsensors
was compiled with sysfs support!
For older kernels, make sure you have done 'modprobe i2c-proc'!
guilherme@Guilherme:~$


meu /etc/modules

# /etc/modules: kernel modules to load at boot time.
#
# This file contains the names of kernel modules that should be loaded
# at boot time, one per line. Lines beginning with "#" are ignored.

lp
i2c-isa
smartbatt
smbus-arp
eeprom
it87

[leandrovargas]

Digite só :

Código: [Selecionar]

sudo modprobe i2c-isa

Código: [Selecionar]

sudo modprobe eeprom

Código: [Selecionar]

sudo modprobe it87e rode o sensors..

Vlw

[joefreire]

msm erro
Can't access procfs/sysfs file
Unable to find i2c bus information;
For 2.6 kernels, make sure you have mounted sysfs and libsensors
was compiled with sysfs support!
For older kernels, make sure you have done 'modprobe i2c-proc'!

[leandrovargas]

rode o sudo sensors-detect de novo, não adicione nada no modules e rode de novo :

Código: [Selecionar]

sudo modprobe i2c-isa

Código: [Selecionar]

sudo modprobe eeprom

Código: [Selecionar]

sudo modprobe it87e rode de novo o sensors..Aqui tambem acontece isso...aí eu tenho que fazer tudo isso...Tenta lá...

Vlw

[joefreire]

mais como deixar o /etc/modules
??

[leandrovargas]

Deixa ele normal como está...

Vlw

[joefreire]

# /etc/modules: kernel modules to load at boot time.
#
# This file contains the names of kernel modules that should be loaded
# at boot time, one per line. Lines beginning with "#" are ignored.

lp


normal e assim ne?:
da o msm erro

 Can't access procfs/sysfs file
Unable to find i2c bus information;
For 2.6 kernels, make sure you have mounted sysfs and libsensors
was compiled with sysfs support!
For older kernels, make sure you have done 'modprobe i2c-proc

[leandrovargas]

Você rodou, de novo, sudo sensors-detect e depois de detectar rodou o sudo modprobe eeprom , sudo modprobe i2c-isa, sudo modprobe it87 e tentou rodar o sensors e deu esse erro de novo??

Vlw

[joefreire]

mesma coisa vei

[leandrovargas]

Tentei aqui no meu sensors e esta dando o mesmo erro..Mas hoje mesmo eu já rodei ele...Isso está muito estranho. Parece que ele funciona, se eu rodar ele logo que entrar no sistema...Vou tentar resolver aqui e retorno para você...

Vlw

[joefreire]

da uma olhada ae vei pq eu presiso muito disso toda hra eu reinicio para olhar a temp
e um saco
vlw