Comando usando o adaptador D-Link DWA 125
description: Ethernet interface
product: RTL8111/8168/8411 PCI Express Gigabit Ethernet Controller
vendor: Realtek Semiconductor Co., Ltd.
physical id: 0
bus info: pci@0000:03:00.0
logical name: eth0
version: 06
serial: 30:85:a9:e9:71:ad
size: 10Mbit/s
capacity: 1Gbit/s
width: 64 bits
clock: 33MHz
capabilities: pm msi pciexpress msix vpd bus_master cap_list ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation
configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=half firmware=rtl8168e-3_0.0.4 03/27/12 latency=0 link=no multicast=yes port=MII speed=10Mbit/s
resources: irq:41 ioport:e000(size=256) memory:f0004000-f0004fff memory:f0000000-f0003fff
*-network
description: Wireless interface
physical id: 3
bus info: usb@1:1.1
logical name: wlan0
serial: 78:54:2e:e8:e4:8e
capabilities: ethernet physical wireless
configuration: broadcast=yes driver=rt2800usb driverversion=3.13.0-24-generic firmware=0.29 ip=192.168.0.102 link=yes multicast=yes wireless=IEEE 802.11bgn
ubuntu@ubuntu:~$ ifconfig
eth0 Link encap:Ethernet HWaddr 30:85:a9:e9:71:ad
UP BROADCAST MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:0 (0.0 B) TX bytes:0 (0.0 B)
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
inet6 addr: ::1/128 Scope:Host
UP LOOPBACK RUNNING MTU:65536 Metric:1
RX packets:437 errors:0 dropped:0 overruns:0 frame:0
TX packets:437 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:61452 (61.4 KB) TX bytes:61452 (61.4 KB)
wlan0 Link encap:Ethernet HWaddr 78:54:2e:e8:e4:8e
inet addr:192.168.0.102 Bcast:192.168.0.255 Mask:255.255.255.0
inet6 addr: fe80::7a54:2eff:fee8:e48e/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:4317 errors:0 dropped:0 overruns:0 frame:0
TX packets:3114 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:4858591 (4.8 MB) TX bytes:415946 (415.9 KB)
ubuntu@ubuntu:~$ iwconfig
eth0 no wireless extensions.
lo no wireless extensions.
wlan0 IEEE 802.11bgn ESSID:"Slayer"
Mode:Managed Frequency:2.452 GHz Access Point: 10:FE:ED:B5:6D:3A
Bit Rate=60 Mb/s Tx-Power=20 dBm
Retry long limit:7 RTS thr:off Fragment thr:off
Power Management:on
Link Quality=43/70 Signal level=-67 dBm
Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0
Tx excessive retries:22 Invalid misc:98 Missed beacon:0
ubuntu@ubuntu:~$ nm-tool
NetworkManager Tool
State: connected (global)
- Device: eth0 -----------------------------------------------------------------
Type: Wired
Driver: r8169
State: unavailable
Default: no
HW Address: 30:85:A9:E9:71:AD
Capabilities:
Carrier Detect: yes
Wired Properties
Carrier: off
- Device: wlan0 [Slayer] ------------------------------------------------------
Type: 802.11 WiFi
Driver: rt2800usb
State: connected
Default: yes
HW Address: 78:54:2E:E8:E4:8E
Capabilities:
Speed: 60 Mb/s
Wireless Properties
WEP Encryption: yes
WPA Encryption: yes
WPA2 Encryption: yes
Wireless Access Points (* = current AP)
jefersina's house: Infra, F4:EC:38:BC:70:08, Freq 2412 MHz, Rate 54 Mb/s, Strength 19 WPA2
c76a3a: Infra, 70:54:D2:C3:56:EF, Freq 2412 MHz, Rate 54 Mb/s, Strength 12 WPA WPA2
c715ce: Infra, 70:54:D2:C6:0C:5F, Freq 2462 MHz, Rate 54 Mb/s, Strength 29 WPA WPA2
PINESE & MOREIRA:Infra, 84:C9:B2:C5:F0:02, Freq 2412 MHz, Rate 54 Mb/s, Strength 12 WPA WPA2
*Slayer: Infra, 10:FE:ED:B5:6D:3A, Freq 2452 MHz, Rate 54 Mb/s, Strength 55 WPA WPA2
IPv4 Settings:
Address: 192.168.0.102
Prefix: 24 (255.255.255.0)
Gateway: 192.168.0.1
DNS: 192.168.0.1
ubuntu@ubuntu:~$ rfkill list wifi
0: phy0: Wireless LAN
Soft blocked: no
Hard blocked: no