Webcam HardCam

[Aika]

Olá à Todos do Forum!

Faz 1 ano que venho utilizando o ubuntu, onde comecei pelo 8.10 e agora estou no 9.04.
Com MUITA dificuldade convenci minha esposa a usa-lo também.
Agora depois de muito tempo e sacrificios ela já se acostumou e eu estava para remover o windows xp que estava em uma segunda partição. AI...
ela comprou uma webcam HardCam para falar com a familia que esta distante e me pediu para instalar a web. Começaram os problemas!
Tentei varios topicos do forum e só piorou meu problema, sumiu icones, parou de entrar nas configurações de video até o ponto de parar de entrar no ubuntu. Ai tive que formatar e instalar de novo... Trabalheira só com um monte de fotos e musicas....!!!!
E até agora não consegui fazer a web funcionar e ainda tive que voltar a instalar o windows Xp para ela usar a webcam...

Será que, por favor, Alguem poderia me ajudar com a Web antes que eu tenha que voltar para o Windows ou acabar em divorcio???
gostaria que funcionace no aMsn e no Skype...

estou deixando aqui o que o lsusb me deu como resposta:

Bus 003 Device 002: ID 0ac8:307b Z-Star Microelectronics Corp. USB 1.1 WebCam

Desde de já agradeço a atenção,
Akira Cardozo

[Ioca100]

Teste aí no Skype se não funcionar , já era, também tenho uma dessa fábrica(Bus 002 Device 002: ID 0ac8:305b Z-Star Microelectronics Corp. ZC0305 Webcam) que não funciona com esses drivers do Linux.

[Tota]

Bem sua cam => ID 0ac8:307b Z-Star Microelectronics Corp

é uma vimicro que deveria funcionar. Veja o link abaixo ( eu não li o mesmo )

http://mxhaard.free.fr/spca5xx.html

Pelo visto ela usa o driver gspca e deveria estar ok.

Veja o resultado de

Código Selecionar Expandir

sudo dmesg

e copie e cole aqui apenas a parte  como  ela foi reconhecida.

[],s

[Ioca100]

Colega Tota, tomando a liberdade do post que não é meu, gostaria que pudesse me ajudar, veja o que está aqui:
14.609570] ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver
[   14.676681] gspca: main v2.6.0 registered
[   15.216630] gspca: probing 0ac8:305b
[   15.216640] zc3xx: Sensor Tas5130 (VF0250)
[   15.222232] gspca: probe ok
[   15.222273] usbcore: registered new interface driver zc3xx
[   15.222278] zc3xx: registered
Mas a webcam não funciona, já testei em vários programas.

[Tota]

Colega Tota, tomando a liberdade do post que não é meu, gostaria que pudesse me ajudar, veja o que está aqui:
14.609570] ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver
[   14.676681] gspca: main v2.6.0 registered
[   15.216630] gspca: probing 0ac8:305b
[   15.216640] zc3xx: Sensor Tas5130 (VF0250)
[   15.222232] gspca: probe ok
[   15.222273] usbcore: registered new interface driver zc3xx
[   15.222278] zc3xx: registered
Mas a webcam não funciona, já testei em vários programas.

Ok, o gspca tambem levantou o modulo zc3xx, da sua cam=> 0ac8:305b

agora o que informa o seu dmesg?

[Ioca100]

Não achei a webcam;



0.784490] usb usb2: configuration #1 chosen from 1 choice
[    0.784519] hub 2-0:1.0: USB hub found
[    0.784528] hub 2-0:1.0: 2 ports detected
[    0.784575] uhci_hcd 0000:00:10.1: PCI INT B -> Link[ALKB] -> GSI 21 (level, low) -> IRQ 21
[    0.784582] uhci_hcd 0000:00:10.1: UHCI Host Controller
[    0.784613] uhci_hcd 0000:00:10.1: new USB bus registered, assigned bus number 3
[    0.784633] uhci_hcd 0000:00:10.1: irq 21, io base 0x0000d400
[    0.784731] usb usb3: configuration #1 chosen from 1 choice
[    0.784759] hub 3-0:1.0: USB hub found
[    0.784770] hub 3-0:1.0: 2 ports detected
[    0.784816] uhci_hcd 0000:00:10.2: PCI INT C -> Link[ALKB] -> GSI 21 (level, low) -> IRQ 21
[    0.784824] uhci_hcd 0000:00:10.2: UHCI Host Controller
[    0.784863] uhci_hcd 0000:00:10.2: new USB bus registered, assigned bus number 4
[    0.784883] uhci_hcd 0000:00:10.2: irq 21, io base 0x0000d800
[    0.784982] usb usb4: configuration #1 chosen from 1 choice
[    0.785009] hub 4-0:1.0: USB hub found
[    0.785021] hub 4-0:1.0: 2 ports detected
[    0.785135] PNP: No PS/2 controller found. Probing ports directly.
[    0.785545] serio: i8042 KBD port at 0x60,0x64 irq 1
[    0.785554] serio: i8042 AUX port at 0x60,0x64 irq 12
[    0.785623] mice: PS/2 mouse device common for all mice
[    0.785739] rtc_cmos 00:05: RTC can wake from S4
[    0.785791] rtc_cmos 00:05: rtc core: registered rtc_cmos as rtc0
[    0.785839] rtc0: alarms up to one year, y3k, 242 bytes nvram
[    0.785921] device-mapper: uevent: version 1.0.3
[    0.786065] device-mapper: ioctl: 4.15.0-ioctl (2009-04-01) initialised: dm-devel@redhat.com
[    0.786178] device-mapper: multipath: version 1.1.0 loaded
[    0.786182] device-mapper: multipath round-robin: version 1.0.0 loaded
[    0.786320] EISA: Probing bus 0 at eisa.0
[    0.786339] Cannot allocate resource for EISA slot 4
[    0.786341] Cannot allocate resource for EISA slot 5
[    0.786354] EISA: Detected 0 cards.
[    0.786459] cpuidle: using governor ladder
[    0.786508] cpuidle: using governor menu
[    0.787052] TCP cubic registered
[    0.787235] NET: Registered protocol family 10
[    0.787726] lo: Disabled Privacy Extensions
[    0.788111] NET: Registered protocol family 17
[    0.788132] Bluetooth: L2CAP ver 2.13
[    0.788134] Bluetooth: L2CAP socket layer initialized
[    0.788138] Bluetooth: SCO (Voice Link) ver 0.6
[    0.788140] Bluetooth: SCO socket layer initialized
[    0.788180] Bluetooth: RFCOMM TTY layer initialized
[    0.788184] Bluetooth: RFCOMM socket layer initialized
[    0.788187] Bluetooth: RFCOMM ver 1.11
[    0.788207] powernow-k8: Processor cpuid 6a0 not supported
[    0.788237] Using IPI No-Shortcut mode
[    0.788310] PM: Resume from disk failed.
[    0.788338] registered taskstats version 1
[    0.788459]   Magic number: 13:537:902
[    0.788614] rtc_cmos 00:05: setting system clock to 2009-10-14 20:51:39 UTC (1255553499)
[    0.788619] BIOS EDD facility v0.16 2004-Jun-25, 0 devices found
[    0.788621] EDD information not available.
[    0.936494] ata1.00: ATA-6: WDC WD800BB-00JHA0, 05.01C05, max UDMA/100
[    0.936498] ata1.00: 156301488 sectors, multi 16: LBA
[    0.944333] ata1.00: configured for UDMA/100
[    0.944519] scsi 0:0:0:0: Direct-Access     ATA      WDC WD800BB-00JH 05.0 PQ: 0 ANSI: 5
[    0.944666] sd 0:0:0:0: Attached scsi generic sg0 type 0
[    0.944719] sd 0:0:0:0: [sda] 156301488 512-byte logical blocks: (80.0 GB/74.5 GiB)
[    0.944778] sd 0:0:0:0: [sda] Write Protect is off
[    0.944781] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[    0.944811] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[    0.944974]  sda: sda1 sda2 sda3
[    0.994580] sd 0:0:0:0: [sda] Attached SCSI disk
[    1.100526] ata2.00: ATAPI: HL-DT-ST GCE-8526B, 1.04, max UDMA/33
[    1.116234] ata2.00: configured for UDMA/33
[    1.116770] scsi 1:0:0:0: CD-ROM            HL-DT-ST CD-RW GCE-8526B  1.04 PQ: 0 ANSI: 5
[    1.145827] sr0: scsi3-mmc drive: 52x/52x writer cd/rw xa/form2 cdda tray
[    1.145831] Uniform CD-ROM driver Revision: 3.20
[    1.145913] sr 1:0:0:0: Attached scsi CD-ROM sr0
[    1.145962] sr 1:0:0:0: Attached scsi generic sg1 type 5
[    1.145994] Freeing unused kernel memory: 540k freed
[    1.146836] Write protecting the kernel text: 4568k
[    1.146870] Write protecting the kernel read-only data: 1836k
[    1.355470] Linux agpgart interface v0.103
[    1.358463] agpgart: Detected VIA KM400/KM400A chipset
[    1.379417] via-rhine.c:v1.10-LK1.4.3 2007-03-06 Written by Donald Becker
[    1.381666] Floppy drive(s): fd0 is 1.44M
[    1.400277] FDC 0 is a post-1991 82077
[    1.521368] usb 2-1: new full speed USB device using uhci_hcd and address 2
[    1.555621] agpgart-via 0000:00:00.0: AGP aperture is 256M @ 0xb0000000
[    1.556182] ACPI: PCI Interrupt Link [ALKD] BIOS reported IRQ 0, using IRQ 23
[    1.556185] ACPI: PCI Interrupt Link [ALKD] enabled at IRQ 23
[    1.556194]   alloc irq_desc for 23 on node -1
[    1.556196]   alloc kstat_irqs on node -1
[    1.556208] via-rhine 0000:00:12.0: PCI INT A -> Link[ALKD] -> GSI 23 (level, low) -> IRQ 23
[    1.557019] eth0: VIA Rhine II at 0xe2001000, 00:00:00:00:00:10, IRQ 23.
[    1.557733] eth0: MII PHY found at address 1, status 0x7869 advertising 05e1 Link 41e1.
[    1.568309] [drm] Initialized drm 1.1.0 20060810
[    1.594055] [drm] radeon default to kernel modesetting DISABLED.
[    1.594107]   alloc irq_desc for 16 on node -1
[    1.594111]   alloc kstat_irqs on node -1
[    1.594122] pci 0000:01:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[    1.594318] [drm] Initialized radeon 1.31.0 20080528 for 0000:01:00.0 on minor 0
[    1.729610] usb 2-1: configuration #1 chosen from 1 choice
[    1.968034] usb 2-2: new low speed USB device using uhci_hcd and address 3
[    2.080040] vesafb: framebuffer at 0xc0000000, mapped to 0xf0a80000, using 1536k, total 131072k
[    2.080047] vesafb: mode is 1024x768x8, linelength=1024, pages=169
[    2.080049] vesafb: protected mode interface info at c000:5841
[    2.080053] vesafb: pmi: set display start = c00c58d5, set palette = c00c5921
[    2.080055] vesafb: pmi: ports = c010 c016 c054 c038 c03c c05c c000 c004 c0b0 c0b2 c0b4
[    2.080062] vesafb: scrolling: redraw
[    2.080066] vesafb: Pseudocolor: size=8:8:8:8, shift=0:0:0:0
[    2.080150] fb0: VESA VGA frame buffer device
[    2.088166] Console: switching to colour frame buffer device 128x48
[    2.152569] usb 2-2: configuration #1 chosen from 1 choice
[    2.162768] usbcore: registered new interface driver hiddev
[    2.175842] input: Microsoft Basic Optical Mouse as /devices/pci0000:00/0000:00:10.0/usb2/2-2/2-2:1.0/input/input4
[    2.175954] generic-usb 0003:045E:0083.0001: input,hidraw0: USB HID v1.10 Mouse [Microsoft Basic Optical Mouse] on usb-0000:00:10.0-2/input0
[    2.175976] usbcore: registered new interface driver usbhid
[    2.175980] usbhid: v2.6:USB HID core driver
[    2.409260] usb 3-1: new low speed USB device using uhci_hcd and address 2
[    2.580824] usb 3-1: configuration #1 chosen from 1 choice
[    2.617153] input: HID Keyboard Device as /devices/pci0000:00/0000:00:10.1/usb3/3-1/3-1:1.0/input/input5
[    2.617278] generic-usb 0003:0E6A:6001.0002: input,hidraw1: USB HID v1.10 Keyboard [HID Keyboard Device] on usb-0000:00:10.1-1/input0
[    2.649789] input: HID Keyboard Device as /devices/pci0000:00/0000:00:10.1/usb3/3-1/3-1:1.1/input/input6
[    2.649903] generic-usb 0003:0E6A:6001.0003: input,hidraw2: USB HID v1.10 Device [HID Keyboard Device] on usb-0000:00:10.1-1/input1
[    7.478743] kjournald starting.  Commit interval 5 seconds
[    7.478759] EXT3-fs: mounted filesystem with writeback data mode.
[    8.366348] type=1505 audit(1255553507.076:2): operation="profile_load" pid=421 name=/usr/share/gdm/guest-session/Xsession
[    8.377469] type=1505 audit(1255553507.087:3): operation="profile_load" pid=422 name=/sbin/dhclient3
[    8.377794] type=1505 audit(1255553507.087:4): operation="profile_load" pid=422 name=/usr/lib/NetworkManager/nm-dhcp-client.action
[    8.377986] type=1505 audit(1255553507.087:5): operation="profile_load" pid=422 name=/usr/lib/connman/scripts/dhclient-script
[    8.409448] type=1505 audit(1255553507.119:6): operation="profile_load" pid=423 name=/usr/bin/evince
[    8.414852] type=1505 audit(1255553507.123:7): operation="profile_load" pid=423 name=/usr/bin/evince-previewer
[    8.418051] type=1505 audit(1255553507.127:: operation="profile_load" pid=423 name=/usr/bin/evince-thumbnailer
[    8.609277] type=1505 audit(1255553507.319:9): operation="profile_load" pid=425 name=/usr/bin/freshclam
[    8.630818] type=1505 audit(1255553507.339:10): operation="profile_load" pid=426 name=/usr/sbin/clamd
[    8.643265] type=1505 audit(1255553507.351:11): operation="profile_load" pid=427 name=/usr/lib/cups/backend/cups-pdf
[   10.329222] Adding 971924k swap on /dev/sda3.  Priority:-1 extents:1 across:971924k
[   11.281115] EXT3 FS on sda2, internal journal
[   11.306789] udev: starting version 147
[   12.753808] Linux video capture interface: v2.00
[   12.762292] gspca: main v2.6.0 registered
[   12.770564] gspca: probing 0ac8:305b
[   12.770575] zc3xx: Sensor Tas5130 (VF0250)
[   12.775293] gspca: probe ok
[   12.775329] usbcore: registered new interface driver zc3xx
[   12.775333] zc3xx: registered
[   12.936622] lp: driver loaded but no devices found
[   13.118383] parport_pc 00:0a: reported by Plug and Play ACPI
[   13.118493] parport0: PC-style at 0x378 (0x778), irq 7, dma 3 [PCSPP,TRISTATE,COMPAT,EPP,ECP,DMA]
[   13.216253] lp0: using parport0 (interrupt-driven).
[   13.333963] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
[   1 of the native dr

[Tota]

Não achei a webcam;

[   12.753808] Linux video capture interface: v2.00
[   12.762292] gspca: main v2.6.0 registered
[   12.770564] gspca: probing 0ac8:305b
[   12.770575] zc3xx: Sensor Tas5130 (VF0250)
[   12.775293] gspca: probe ok
[   12.775329] usbcore: registered new interface driver zc3xx
[   12.775333] zc3xx: registered

[   1 of the native dr

Ficou faltando o fim do dmesg, mas a cam está sendo vista, faltando atribuir um device para ela

[Ioca100]

O final do pedido;
[   15.819015] Linux video capture interface: v2.00
[   15.865836] gspca: main v2.6.0 registered
[   15.874198] gspca: probing 0ac8:305b
[   15.874209] zc3xx: Sensor Tas5130 (VF0250)
[   15.879022] gspca: probe ok
[   15.879058] usbcore: registered new interface driver zc3xx
[   15.879063] zc3xx: registered
[   16.008500] lp: driver loaded but no devices found
[   16.786877] parport_pc 00:0a: reported by Plug and Play ACPI
[   16.786995] parport0: PC-style at 0x378 (0x778), irq 7, dma 3 [PCSPP,TRISTATE,COMPAT,EPP,ECP,DMA]
[   16.884224] lp0: using parport0 (interrupt-driven).
[   17.840940] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
[   17.848721] ppdev: user-space parallel port driver
[   18.424491] irda_init()
[   18.424524] NET: Registered protocol family 23
[   18.728436] w83627hf: Found W83697HF chip at 0x290
[   18.728480] ACPI: I/O resource w83627hf [0x295-0x296] conflicts with ACPI region IP__ [0x295-0x296]
[   18.728485] ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver
[   18.735333] w83627hf: Found W83697HF chip at 0x290
[   18.735375] ACPI: I/O resource w83627hf [0x295-0x296] conflicts with ACPI region IP__ [0x295-0x296]
[   18.735381] ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver
[   18.743772] w83627hf: Found W83697HF chip at 0x290
[   18.743815] ACPI: I/O resource w83627hf [0x295-0x296] conflicts with ACPI region IP__ [0x295-0x296]
[   18.743821] ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver
[   18.907330] ip_tables: (C) 2000-2006 Netfilter Core Team
[   20.858493] __ratelimit: 9 callbacks suppressed
[   20.858499] type=1505 audit(1255603319.567:15): operation="profile_replace" pid=852 name=/usr/share/gdm/guest-session/Xsession
[   20.861117] type=1505 audit(1255603319.571:16): operation="profile_replace" pid=853 name=/sbin/dhclient3
[   20.861449] type=1505 audit(1255603319.571:17): operation="profile_replace" pid=853 name=/usr/lib/NetworkManager/nm-dhcp-client.action
[   20.861644] type=1505 audit(1255603319.571:18): operation="profile_replace" pid=853 name=/usr/lib/connman/scripts/dhclient-script
[   20.872508] type=1505 audit(1255603319.583:19): operation="profile_replace" pid=854 name=/usr/bin/evince
[   20.878806] type=1505 audit(1255603319.587:20): operation="profile_replace" pid=854 name=/usr/bin/evince-previewer
[   20.883237] type=1505 audit(1255603319.591:21): operation="profile_replace" pid=854 name=/usr/bin/evince-thumbnailer
[   21.004954] type=1505 audit(1255603319.715:22): operation="profile_replace" pid=856 name=/usr/bin/freshclam
[   21.008530] type=1505 audit(1255603319.719:23): operation="profile_replace" pid=859 name=/usr/sbin/clamd
[   21.012554] type=1505 audit(1255603319.723:24): operation="profile_replace" pid=860 name=/usr/lib/cups/backend/cups-pdf
[   21.578860] nf_conntrack version 0.5.0 (12287 buckets, 49148 max)
[   21.579212] CONFIG_NF_CT_ACCT is deprecated and will be removed soon. Please use
[   21.579214] nf_conntrack.acct=1 kernel parameter, acct=1 nf_conntrack module option or
[   21.579217] sysctl net.netfilter.nf_conntrack_acct=1 to enable it.
[   22.882877] ACPI: PCI Interrupt Link [ALKC] BIOS reported IRQ 0, using IRQ 22
[   22.882883] ACPI: PCI Interrupt Link [ALKC] enabled at IRQ 22
[   22.882891]   alloc irq_desc for 22 on node -1
[   22.882893]   alloc kstat_irqs on node -1
[   22.882905] VIA 82xx Audio 0000:00:11.5: PCI INT C -> Link[ALKC] -> GSI 22 (level, low) -> IRQ 22
[   22.883073] VIA 82xx Audio 0000:00:11.5: setting latency timer to 64
[   23.394425] codec_read: codec 0 is not valid [0xfe0000]
[   23.400748] codec_read: codec 0 is not valid [0xfe0000]
[   23.407614] codec_read: codec 0 is not valid [0xfe0000]
[   23.413901] codec_read: codec 0 is not valid [0xfe0000]
[   26.153583] eth0: link up, 100Mbps, full-duplex, lpa 0x41E1
[   28.218528] __ratelimit: 9 callbacks suppressed
[   28.218534] type=1503 audit(1255603326.927:28): operation="open" pid=1501 parent=1278 profile="/usr/sbin/clamd" requested_mask="::r" denied_mask="::r" fsuid=112 ouid=0 name="/usr/local/lib/libclamav.so.6.0.2"
[   28.425864] type=1503 audit(1255603327.135:29): operation="open" pid=1501 parent=1278 profile="/usr/sbin/clamd" requested_mask="::r" denied_mask="::r" fsuid=112 ouid=0 name="/usr/local/lib/libclamunrar_iface.so.6.0.2"
[   28.425952] type=1503 audit(1255603327.135:30): operation="open" pid=1501 parent=1278 profile="/usr/sbin/clamd" requested_mask="::r" denied_mask="::r" fsuid=112 ouid=0 name="/usr/local/lib/libclamunrar_iface.a"
[   30.264321] agpgart-via 0000:00:00.0: AGP 3.5 bridge
[   30.264348] agpgart-via 0000:00:00.0: putting AGP V3 device into 8x mode
[   30.264395] pci 0000:01:00.0: putting AGP V3 device into 8x mode
[   30.708435] [drm] Setting GART location based on new memory map
[   30.708448] [drm] Loading R300 Microcode
[   30.708487] [drm] Num pipes: 1
[   30.708494] [drm] writeback test succeeded in 1 usecs
[   36.357194] type=1502 audit(1255603335.067:31): operation="open" pid=1791 parent=1694 profile="/usr/bin/freshclam" requested_mask="::r" denied_mask="::r" fsuid=112 ouid=0 name="/usr/local/lib/libclamav.so.6.0.2"
[   36.357212] type=1502 audit(1255603335.067:32): operation="file_perm" pid=1791 parent=1694 profile="/usr/bin/freshclam" requested_mask="::r" denied_mask="::r" fsuid=112 ouid=0 name="/usr/local/lib/libclamav.so.6.0.2"
[   36.364173] type=1502 audit(1255603335.075:33): operation="file_mmap" pid=1791 parent=1694 profile="/usr/bin/freshclam" requested_mask="::mr" denied_mask="::mr" fsuid=112 ouid=0 name="/usr/local/lib/libclamav.so.6.0.2"
[   36.364197] type=1502 audit(1255603335.075:34): operation="file_mmap" pid=1791 parent=1694 profile="/usr/bin/freshclam" requested_mask="::r" denied_mask="::r" fsuid=112 ouid=0 name="/usr/local/lib/libclamav.so.6.0.2"
[   36.466350] type=1502 audit(1255603335.175:35): operation="file_mprotect" pid=1791 parent=1694 profile="/usr/bin/freshclam" requested_mask="::r" denied_mask="::r" fsuid=112 ouid=0 name="/usr/local/lib/libclamav.so.6.0.2"
[   36.784024] eth0: no IPv6 routers present
[   57.525235] glxinfo:2597 freeing invalid memtype b0102000-b0112000
[   57.525247] glxinfo:2597 freeing invalid memtype b0112000-b0122000
[   57.525255] glxinfo:2597 freeing invalid memtype b0122000-b0132000
[   57.525262] glxinfo:2597 freeing invalid memtype b0132000-b0142000
[   57.525269] glxinfo:2597 freeing invalid memtype b0142000-b0152000
[   57.525276] glxinfo:2597 freeing invalid memtype b0152000-b0162000
[   57.525283] glxinfo:2597 freeing invalid memtype b0162000-b0172000
[   57.525290] glxinfo:2597 freeing invalid memtype b0172000-b0182000
[   57.525297] glxinfo:2597 freeing invalid memtype b0182000-b0192000
[   57.525304] glxinfo:2597 freeing invalid memtype b0192000-b01a2000
[   57.525311] glxinfo:2597 freeing invalid memtype b01a2000-b01b2000
[   57.525318] glxinfo:2597 freeing invalid memtype b01b2000-b01c2000
[   57.525325] glxinfo:2597 freeing invalid memtype b01c2000-b01d2000
[   57.525332] glxinfo:2597 freeing invalid memtype b01d2000-b01e2000
[   57.525340] glxinfo:2597 freeing invalid memtype b01e2000-b01f2000
[   57.525347] glxinfo:2597 freeing invalid memtype b01f2000-b0202000
[   57.525354] glxinfo:2597 freeing invalid memtype b0202000-b0212000
[   57.525361] glxinfo:2597 freeing invalid memtype b0212000-b0222000
[   57.525368] glxinfo:2597 freeing invalid memtype b0222000-b0232000
[   57.525375] glxinfo:2597 freeing invalid memtype b0232000-b0242000
[   57.525382] glxinfo:2597 freeing invalid memtype b0242000-b0252000
[   57.525389] glxinfo:2597 freeing invalid memtype b0252000-b0262000
[   57.525396] glxinfo:2597 freeing invalid memtype b0262000-b0272000
[   57.525403] glxinfo:2597 freeing invalid memtype b0272000-b0282000
[   57.525411] glxinfo:2597 freeing invalid memtype b0282000-b0292000
[   57.525418] glxinfo:2597 freeing invalid memtype b0292000-b02a2000
[   57.525425] glxinfo:2597 freeing invalid memtype b02a2000-b02b2000
[   57.525432] glxinfo:2597 freeing invalid memtype b02b2000-b02c2000
[   57.525439] glxinfo:2597 freeing invalid memtype b02c2000-b02d2000
[   57.525446] glxinfo:2597 freeing invalid memtype b02d2000-b02e2000
[   57.525453] glxinfo:2597 freeing invalid memtype b02e2000-b02f2000
[   57.525459] glxinfo:2597 freeing invalid memtype b02f2000-b0302000

Tota, como atribuo o device?
Mais uma vez te agradeço pela atenção.

[Tota]

com a cam conectada

de um

Código Selecionar Expandir

sudo modprobe zc3xx

e verifique no final do dmesg se atribuiu um /dev/videoX, onde x é o dispositivo

[],s

[Ioca100]

Veja o resultado:

WARNING: All config files need .conf: /etc/modprobe.d/dkms, it will be ignored in a future release.
FATAL: Module zc3xx not found.

[Tota]

bom, se o SO não encontrou o modulo, de um google para zc3xx para saber como instalar

Esta semana eu estou só acessando por celular o que para mim fica dificil ajudar mais

[Ioca100]

bom, se o SO não encontrou o modulo, de um google para zc3xx para saber como instalar

Esta semana eu estou só acessando por celular o que para mim fica dificil ajudar mais

Valeu irmão, vou continuar tentando , mais cedo ou mais tarde conseguirei.

abs.

[Ioca100]

Olá à Todos do Forum!

Faz 1 ano que venho utilizando o ubuntu, onde comecei pelo 8.10 e agora estou no 9.04.
Com MUITA dificuldade convenci minha esposa a usa-lo também.
Agora depois de muito tempo e sacrificios ela já se acostumou e eu estava para remover o windows xp que estava em uma segunda partição. AI...
ela comprou uma webcam HardCam para falar com a familia que esta distante e me pediu para instalar a web. Começaram os problemas!
Tentei varios topicos do forum e só piorou meu problema, sumiu icones, parou de entrar nas configurações de video até o ponto de parar de entrar no ubuntu. Ai tive que formatar e instalar de novo... Trabalheira só com um monte de fotos e musicas....!!!!
E até agora não consegui fazer a web funcionar e ainda tive que voltar a instalar o windows Xp para ela usar a webcam...

Será que, por favor, Alguem poderia me ajudar com a Web antes que eu tenha que voltar para o Windows ou acabar em divorcio???
gostaria que funcionace no aMsn e no Skype...

estou deixando aqui o que o lsusb me deu como resposta:

Bus 003 Device 002: ID 0ac8:307b Z-Star Microelectronics Corp. USB 1.1 WebCam

Desde de já agradeço a atenção,
Akira Cardozo

Veja:       http://www.vivaolinux.com.br/topico/Webcam/Webcam-com-Chip-ZStar.    ,copie e cole na barra de endereço.
 

[Aika]

Olá pessoal!

desculpe a demora em responder... ando meio atarefado!
bem, tentei todas as opções deixadas aqui, mais nenhuma foi satisfatória!
Tentei de varias formas e maneiras possíveis... mais no final por incrível que pareça reiniciei o computador e a cam funcionou no skype depois que coloquei os drivers da v4l para rodas... Blz.. 1 problema foi solucionado...
já no amsn descobri que não funciona com no msn.. ele não tem suporte para video conferencia( não funciona para eu ver a pessoa e a pessoa me ver ao mesmo tempo).
Ai vai outra pergunta seguindo o problema, qual o programa que devo usar para usar a cam com no msn? eu vendo a pessoa e a pessoa me vendo ao mesmo tempo?

Obrigado pela grande ajuda!
Akira

[sboorbou]

desculpe, mas qual versão do ams você esta usando?
minha versão é a 0.97.2~debian-2ubuntu2  e funciona normal.... uso a can do notebook um vostro 1520 e  funfa normal.... ( bem até agora, só isso funfa a can,,, não consegui usar ela para outras cositas mais....  )

digita dpkg -s amsn e me diz a versão

você esta usando algum plugin?