Minha placa de rede não funciona Sis190

edublind · 13 de Novembro de 2007, 11:07

Então istalei aqui o Ubuntu Gutsy e não consigo navegar na internet.
ele simplesmente não funciona!!!
o Ubuntu reconheceu minha placa como uma SIS190n
o que poderia ser???
alguem tem ideia???
Alias ele pega ip e tudo só não funciona
não abre site nenhum não reconhece minha rede
e nem quando eu ligo ele direto no virtua ou no ajato
ja que tenho 2 provedores aqui pra redundancia.

Junior_Sampa · 13 de Novembro de 2007, 11:41

Olá,

Veja se este link te ajuda... é exatamente sobre a SIS190...

http://linuxparaoresgate.com/artigos/resolvendo_problemas_de_hardware_no_linux.php

Abraço
Junior

edublind · 13 de Novembro de 2007, 14:12

Então eu ja havia tentado esse método mas não funcionou mesmo por que a msg que recebo não é a mesma do post

eduardo@eduardo-desktop:~$ sudo dmesg | grep '00:04.0'
[ 264.587901] ACPI: PCI Interrupt 0000:00:04.0[A] -> GSI 19 (level, low) -> IRQ 23
[ 264.587914] PCI: Setting latency timer of device 0000:00:04.0 to 64
[ 264.601305] 0000:00:04.0: Read MAC address from APC.
[ 264.633261] 0000:00:04.0: Broadcom PHY AC131 transceiver at address 0.
[ 265.177194] 0000:00:04.0: SiS 190 PCI Fast Ethernet adapter at f8ce4c00 (IRQ: 23), 00:19:21:9b:97:6a

vou colar tbmm o Retorno do LS PCI talvez ajude.
lspci -nn
00:00.0 Host bridge [0600]: Silicon Integrated Systems [SiS] 761/M761 Host [1039:0761] (rev 01)
00:01.0 PCI bridge [0604]: Silicon Integrated Systems [SiS] PCI-to-PCI bridge [1039:0004]
00:02.0 ISA bridge [0601]: Silicon Integrated Systems [SiS] SiS965 [MuTIOL Media IO] [1039:0965] (rev 48)
00:02.5 IDE interface [0101]: Silicon Integrated Systems [SiS] 5513 [IDE] [1039:5513] (rev 01)
00:02.7 Multimedia audio controller [0401]: Silicon Integrated Systems [SiS] AC'97 Sound Controller [1039:7012] (rev a0)
00:03.0 USB Controller [0c03]: Silicon Integrated Systems [SiS] USB 1.0 Controller [1039:7001] (rev 0f)
00:03.1 USB Controller [0c03]: Silicon Integrated Systems [SiS] USB 1.0 Controller [1039:7001] (rev 0f)
00:03.2 USB Controller [0c03]: Silicon Integrated Systems [SiS] USB 1.0 Controller [1039:7001] (rev 0f)
00:03.3 USB Controller [0c03]: Silicon Integrated Systems [SiS] USB 2.0 Controller [1039:7002]
00:04.0 Ethernet controller [0200]: Silicon Integrated Systems [SiS] 190 Gigabit Ethernet Adapter [1039:0190]
00:05.0 IDE interface [0101]: Silicon Integrated Systems [SiS] 182 SATA/RAID Controller [1039:0182] (rev 01)
00:06.0 PCI bridge [0604]: Silicon Integrated Systems [SiS] PCI-to-PCI bridge [1039:000a]
00:07.0 PCI bridge [0604]: Silicon Integrated Systems [SiS] PCI-to-PCI bridge [1039:000a]
00:18.0 Host bridge [0600]: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] HyperTransport Technology Configuration [1022:1100]
00:18.1 Host bridge [0600]: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Address Map [1022:1101]
00:18.2 Host bridge [0600]: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] DRAM Controller [1022:1102]
00:18.3 Host bridge [0600]: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Miscellaneous Control [1022:1103]
01:00.0 VGA compatible controller [0300]: ATI Technologies Inc Unknown device [1002:94c3]
01:00.1 Audio device [0403]: ATI Technologies Inc Unknown device [1002:aa10]

Obrigado pela ajuda.

Junior_Sampa · 13 de Novembro de 2007, 14:36

Neste caso não sei como te ajudar...

Melhor esperar alguém mais experiente na resolução de problemas de configuração de hardware.

Abrs.
Junior

edublind · 14 de Novembro de 2007, 15:30

Como não consegui resolver o problema comprei outra placa de rede.
Uma RTL8139D
mas ela tbmm nao funcionou
ela simplesmente não está disponivel para uso no ubuntu
isso está me trazendo grandes problemas HELPPPPPP
vou colar o lspci e o dmesg
espero que me ajudemm

eduardo@eduardo-desktop:~$ sudo dmesg
[ 0.000000] Linux version 2.6.22-14-generic (buildd@palmer) (gcc version 4.1.3 20070929 (prerelease) (Ubuntu 4.1.2-16ubuntu2)) #1 SMP Sun Oct 14 23:05:12 GMT 2007 (Ubuntu 2.6.22-14.46-generic)
[ 0.000000] BIOS-provided physical RAM map:
[ 0.000000] BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
[ 0.000000] BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
[ 0.000000] BIOS-e820: 00000000000e6000 - 0000000000100000 (reserved)
[ 0.000000] BIOS-e820: 0000000000100000 - 000000005ffc0000 (usable)
[ 0.000000] BIOS-e820: 000000005ffc0000 - 000000005ffce000 (ACPI data)
[ 0.000000] BIOS-e820: 000000005ffce000 - 000000005fff0000 (ACPI NVS)
[ 0.000000] BIOS-e820: 000000005fff0000 - 0000000060000000 (reserved)
[ 0.000000] BIOS-e820: 00000000ff780000 - 0000000100000000 (reserved)
[ 0.000000] 639MB HIGHMEM available.
[ 0.000000] 896MB LOWMEM available.
[ 0.000000] found SMP MP-table at 000ff780
[ 0.000000] Entering add_active_range(0, 0, 393152) 0 entries of 256 used
[ 0.000000] Zone PFN ranges:
[ 0.000000] DMA 0 -> 4096
[ 0.000000] Normal 4096 -> 229376
[ 0.000000] HighMem 229376 -> 393152
[ 0.000000] early_node_map[1] active PFN ranges
[ 0.000000] 0: 0 -> 393152
[ 0.000000] On node 0 totalpages: 393152
[ 0.000000] DMA zone: 32 pages used for memmap
[ 0.000000] DMA zone: 0 pages reserved
[ 0.000000] DMA zone: 4064 pages, LIFO batch:0
[ 0.000000] Normal zone: 1760 pages used for memmap
[ 0.000000] Normal zone: 223520 pages, LIFO batch:31
[ 0.000000] HighMem zone: 1279 pages used for memmap
[ 0.000000] HighMem zone: 162497 pages, LIFO batch:31
[ 0.000000] DMI 2.3 present.
[ 0.000000] ACPI: RSDP signature @ 0xC00F86E0 checksum 0
[ 0.000000] ACPI: RSDP 000F86E0, 0014 (r0 ACPIAM)
[ 0.000000] ACPI: RSDT 5FFC0000, 0034 (r1 A M I OEMRSDT 2000702 MSFT 97)
[ 0.000000] ACPI: FACP 5FFC0200, 0084 (r2 A M I OEMFACP 2000702 MSFT 97)
[ 0.000000] ACPI: DSDT 5FFC0430, 41BE (r1 1AAAA 1AAAA000 0 INTL 2002026)
[ 0.000000] ACPI: FACS 5FFCE000, 0040
[ 0.000000] ACPI: APIC 5FFC0390, 005C (r1 A M I OEMAPIC 2000702 MSFT 97)
[ 0.000000] ACPI: MCFG 5FFC03F0, 003C (r1 A M I OEMMCFG 2000702 MSFT 97)
[ 0.000000] ACPI: OEMB 5FFCE040, 0046 (r1 A M I AMI_OEM 2000702 MSFT 97)
[ 0.000000] ACPI: PM-Timer IO Port: 0x808
[ 0.000000] ACPI: Local APIC address 0xfee00000
[ 0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
[ 0.000000] Processor #0 15:15 APIC version 16
[ 0.000000] ACPI: LAPIC (acpi_id[0x02] lapic_id[0x81] disabled)
[ 0.000000] ACPI: IOAPIC (id[0x01] address[0xfec00000] gsi_base[0])
[ 0.000000] IOAPIC[0]: apic_id 1, version 20, address 0xfec00000, GSI 0-23
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 low level)
[ 0.000000] ACPI: IRQ0 used by override.
[ 0.000000] ACPI: IRQ2 used by override.
[ 0.000000] ACPI: IRQ9 used by override.
[ 0.000000] Enabling APIC mode: Flat. Using 1 I/O APICs
[ 0.000000] Using ACPI (MADT) for SMP configuration information
[ 0.000000] Allocating PCI resources starting at 70000000 (gap: 60000000:9f780000)
[ 0.000000] Built 1 zonelists. Total pages: 390081
[ 0.000000] Kernel command line: root=UUID=99802726-9421-4343-b04f-ef1cf7610d9c ro quiet splash
[ 0.000000] mapped APIC to ffffd000 (fee00000)
[ 0.000000] mapped IOAPIC to ffffc000 (fec00000)
[ 0.000000] Enabling fast FPU save and restore... done.
[ 0.000000] Enabling unmasked SIMD FPU exception support... done.
[ 0.000000] Initializing CPU#0
[ 0.000000] PID hash table entries: 4096 (order: 12, 16384 bytes)
[ 0.000000] Detected 1600.132 MHz processor.
[ 10.806788] Console: colour VGA+ 80x25
[ 10.807180] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
[ 10.807854] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
[ 10.861018] Memory: 1547156k/1572608k available (2015k kernel code, 24300k reserved, 916k data, 364k init, 655104k highmem)
[ 10.861030] virtual kernel memory layout:
[ 10.861031] fixmap : 0xfff4d000 - 0xfffff000 ( 712 kB)
[ 10.861033] pkmap : 0xff800000 - 0xffc00000 (4096 kB)
[ 10.861034] vmalloc : 0xf8800000 - 0xff7fe000 ( 111 MB)
[ 10.861036] lowmem : 0xc0000000 - 0xf8000000 ( 896 MB)
[ 10.861037] .init : 0xc03e3000 - 0xc043e000 ( 364 kB)
[ 10.861039] .data : 0xc02f7d26 - 0xc03dce84 ( 916 kB)
[ 10.861040] .text : 0xc0100000 - 0xc02f7d26 (2015 kB)
[ 10.861044] Checking if this processor honours the WP bit even in supervisor mode... Ok.
[ 10.861085] SLUB: Genslabs=22, HWalign=64, Order=0-1, MinObjects=4, CPUs=1, Nodes=1
[ 10.940986] Calibrating delay using timer specific routine.. 3201.89 BogoMIPS (lpj=6403797)
[ 10.941015] Security Framework v1.0.0 initialized
[ 10.941022] SELinux: Disabled at boot.
[ 10.941036] Mount-cache hash table entries: 512
[ 10.941163] CPU: After generic identify, caps: 078bfbff ebd3fbff 00000000 00000000 00002001 00000000 00000019
[ 10.941173] CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
[ 10.941176] CPU: L2 Cache: 256K (64 bytes/line)
[ 10.941179] CPU: After all inits, caps: 078bfbff ebd3fbff 00000000 00000410 00002001 00000000 00000019
[ 10.941190] Compat vDSO mapped to ffffe000.
[ 10.941202] Checking 'hlt' instruction... OK.
[ 10.957103] SMP alternatives: switching to UP code
[ 10.957301] Freeing SMP alternatives: 11k freed
[ 10.957600] Early unpacking initramfs... done
[ 11.329978] ACPI: Core revision 20070126
[ 11.330045] ACPI: Looking for DSDT in initramfs... error, file /DSDT.aml not found.
[ 11.331917] CPU0: AMD Sempron(tm) Processor 3000+ stepping 02
[ 11.331936] Total of 1 processors activated (3201.89 BogoMIPS).
[ 11.332029] ENABLING IO-APIC IRQs
[ 11.332193] ..TIMER: vector=0x31 apic1=0 pin1=2 apic2=-1 pin2=-1
[ 11.476248] Brought up 1 CPUs
[ 11.476351] Booting paravirtualized kernel on bare hardware
[ 11.476413] Time: 15:03:12 Date: 10/14/107
[ 11.476436] NET: Registered protocol family 16
[ 11.476520] EISA bus registered
[ 11.476532] ACPI: bus type pci registered
[ 11.477208] PCI: PCI BIOS revision 3.00 entry at 0xf0031, last bus=3
[ 11.477210] PCI: Using configuration type 1
[ 11.477212] Setting up standard PCI resources
[ 11.486008] ACPI: EC: Look up EC in DSDT
[ 11.491188] ACPI: Interpreter enabled
[ 11.491191] ACPI: (supports S0 S1 S3 S4 S5)
[ 11.491207] ACPI: Using IOAPIC for interrupt routing
[ 11.491422] Error attaching device data
[ 11.491427] Error attaching device data
[ 11.500501] ACPI: PCI Root Bridge [PCI0] (0000:00)
[ 11.500509] PCI: Probing PCI hardware (bus 00)
[ 11.501243] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
[ 11.501421] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P6._PRT]
[ 11.501496] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P7._PRT]
[ 11.510496] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 7 *10 11 12 14 15)
[ 11.510606] ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 *5 7 10 11 12 14 15)
[ 11.510714] ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 7 10 *11 12 14 15)
[ 11.510820] ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 *5 7 10 11 12 14 15)
[ 11.510927] ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 *5 7 10 11 12 14 15)
[ 11.511038] ACPI: PCI Interrupt Link [LNKF] (IRQs *3 4 5 7 10 11 12 14 15)
[ 11.511147] ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 7 *10 11 12 14 15)
[ 11.511256] ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 7 10 *11 12 14 15)
[ 11.511340] Linux Plug and Play Support v0.97 (c) Adam Belay
[ 11.511351] pnp: PnP ACPI init
[ 11.511363] ACPI: bus type pnp registered
[ 11.517472] pnp: PnP ACPI: found 15 devices
[ 11.517475] ACPI: ACPI bus type pnp unregistered
[ 11.517479] PnPBIOS: Disabled by ACPI PNP
[ 11.517529] PCI: Using ACPI for IRQ routing
[ 11.517532] PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report
[ 11.522669] NET: Registered protocol family 8
[ 11.522672] NET: Registered protocol family 20
[ 11.522741] pnp: 00:0a: ioport range 0xa00-0xa0f has been reserved
[ 11.522745] pnp: 00:0a: ioport range 0xa10-0xa1f has been reserved
[ 11.522748] pnp: 00:0a: ioport range 0xa20-0xa2f has been reserved
[ 11.522751] pnp: 00:0a: ioport range 0xa30-0xa3f has been reserved
[ 11.522757] pnp: 00:0b: iomem range 0xfff80000-0xffffffff could not be reserved
[ 11.522761] pnp: 00:0b: iomem range 0xffb80000-0xffbfffff could not be reserved
[ 11.522765] pnp: 00:0b: iomem range 0xffee0000-0xffefffff could not be reserved
[ 11.522770] pnp: 00:0c: iomem range 0xfec00000-0xfec00fff has been reserved
[ 11.522774] pnp: 00:0c: iomem range 0xfee00000-0xfee00fff has been reserved
[ 11.522780] pnp: 00:0d: iomem range 0xe0000000-0xefffffff has been reserved
[ 11.522785] pnp: 00:0e: iomem range 0x0-0x9ffff could not be reserved
[ 11.522788] pnp: 00:0e: iomem range 0xc0000-0xcffff could not be reserved
[ 11.522792] pnp: 00:0e: iomem range 0xe0000-0xfffff could not be reserved
[ 11.522795] pnp: 00:0e: iomem range 0x100000-0x5fffffff could not be reserved
[ 11.524146] Time: tsc clocksource has been installed.
[ 11.553027] PCI: Bridge: 0000:00:01.0
[ 11.553029] IO window: e000-efff
[ 11.553034] MEM window: feb00000-febfffff
[ 11.553038] PREFETCH window: d0000000-dfffffff
[ 11.553042] PCI: Bridge: 0000:00:06.0
[ 11.553044] IO window: disabled.
[ 11.553047] MEM window: disabled.
[ 11.553050] PREFETCH window: disabled.
[ 11.553054] PCI: Bridge: 0000:00:07.0
[ 11.553055] IO window: disabled.
[ 11.553059] MEM window: disabled.
[ 11.553062] PREFETCH window: disabled.
[ 11.553081] PCI: Setting latency timer of device 0000:00:01.0 to 64
[ 11.553095] PCI: Setting latency timer of device 0000:00:06.0 to 64
[ 11.553108] PCI: Setting latency timer of device 0000:00:07.0 to 64
[ 11.553123] NET: Registered protocol family 2
[ 11.592085] IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 11.592201] TCP established hash table entries: 131072 (order: 8, 1572864 bytes)
[ 11.593614] TCP bind hash table entries: 65536 (order: 7, 524288 bytes)
[ 11.594083] TCP: Hash tables configured (established 131072 bind 65536)
[ 11.594087] TCP reno registered
[ 11.604160] checking if image is initramfs... it is
[ 12.055376] Switched to high resolution mode on CPU 0
[ 12.333237] Freeing initrd memory: 7327k freed
[ 12.333596] audit: initializing netlink socket (disabled)
[ 12.333608] audit(1195052592.060:1): initialized
[ 12.333668] highmem bounce pool size: 64 pages
[ 12.335354] VFS: Disk quotas dquot_6.5.1
[ 12.335405] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 12.335500] io scheduler noop registered
[ 12.335502] io scheduler anticipatory registered
[ 12.335504] io scheduler deadline registered
[ 12.335520] io scheduler cfq registered (default)
[ 12.335561] Boot video device is 0000:01:00.0
[ 12.335631] PCI: Setting latency timer of device 0000:00:01.0 to 64
[ 12.335658] assign_interrupt_mode Found MSI capability
[ 12.335661] Allocate Port Service[0000:00:01.0:pcie00]
[ 12.335730] PCI: Setting latency timer of device 0000:00:06.0 to 64
[ 12.335766] assign_interrupt_mode Found MSI capability
[ 12.335769] Allocate Port Service[0000:00:06.0:pcie00]
[ 12.335836] PCI: Setting latency timer of device 0000:00:07.0 to 64
[ 12.335872] assign_interrupt_mode Found MSI capability
[ 12.335874] Allocate Port Service[0000:00:07.0:pcie00]
[ 12.335994] isapnp: Scanning for PnP cards...
[ 12.688999] isapnp: No Plug & Play device found

edublind · 14 de Novembro de 2007, 15:30

Ai vai o resto da msg

[ 12.715765] Real Time Clock Driver v1.12ac
[ 12.715846] Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
[ 12.715934] serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[ 12.716748] 00:07: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[ 12.717423] RAMDISK driver initialized: 16 RAM disks of 65536K size 1024 blocksize
[ 12.717588] input: Macintosh mouse button emulation as /class/input/input0
[ 12.717659] PNP: PS/2 Controller [PNP0303:PS2K,PNP0f03:PS2M] at 0x60,0x64 irq 1,12
[ 12.717927] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 12.717932] serio: i8042 AUX port at 0x60,0x64 irq 12
[ 12.718068] mice: PS/2 mouse device common for all mice
[ 12.718164] EISA: Probing bus 0 at eisa.0
[ 12.718201] EISA: Detected 0 cards.
[ 12.718364] TCP cubic registered
[ 12.718383] NET: Registered protocol family 1
[ 12.718408] Using IPI No-Shortcut mode
[ 12.718573] Magic number: 15:186:83
[ 12.718967] Freeing unused kernel memory: 364k freed
[ 12.758323] input: AT Translated Set 2 keyboard as /class/input/input1
[ 13.973745] AppArmor: AppArmor initialized<5>audit(1195052593.560:2): type=1505 info="AppArmor initialized" pid=1204
[ 13.981278] fuse init (API version 7.

[ 13.986893] Failure registering capabilities with primary security module.
[ 14.007628] ACPI: Processor [P001] (supports 8 throttling states)
[ 14.007641] ACPI Exception (processor_core-0783): AE_NOT_FOUND, Processor Device is not present [20070126]
[ 14.678442] SCSI subsystem initialized
[ 14.683219] libata version 2.21 loaded.
[ 14.686620] pata_sis 0000:00:02.5: version 0.5.1
[ 14.686648] ACPI: PCI Interrupt 0000:00:02.5[A] -> GSI 16 (level, low) -> IRQ 16
[ 14.686740] scsi0 : pata_sis
[ 14.686777] scsi1 : pata_sis
[ 14.686876] ata1: PATA max UDMA/133 cmd 0x000101f0 ctl 0x000103f6 bmdma 0x0001ffa0 irq 14
[ 14.686880] ata2: PATA max UDMA/133 cmd 0x00010170 ctl 0x00010376 bmdma 0x0001ffa8 irq 15
[ 14.721989] usbcore: registered new interface driver usbfs
[ 14.722014] usbcore: registered new interface driver hub
[ 14.722034] usbcore: registered new device driver usb
[ 14.747263] ohci_hcd: 2006 August 04 USB 1.1 'Open' Host Controller (OHCI) Driver
[ 14.994222] Floppy drive(s): fd0 is 1.44M
[ 15.003118] ata1.01: ATAPI: HL-DT-STDVD-RAM GSA-H22N, 1.01, max UDMA/66
[ 15.042492] FDC 0 is a post-1991 82077
[ 15.174827] ata1.01: configured for UDMA/66
[ 15.331602] scsi 0:0:1:0: CD-ROM HL-DT-ST DVD-RAM GSA-H22N 1.01 PQ: 0 ANSI: 5
[ 15.331975] ACPI: PCI Interrupt 0000:00:03.0[A] -> GSI 20 (level, low) -> IRQ 17
[ 15.331988] ohci_hcd 0000:00:03.0: OHCI Host Controller
[ 15.332147] ohci_hcd 0000:00:03.0: new USB bus registered, assigned bus number 1
[ 15.332165] ohci_hcd 0000:00:03.0: irq 17, io mem 0xfeaff000
[ 15.351214] sr0: scsi3-mmc drive: 48x/48x writer dvd-ram cd/rw xa/form2 cdda tray
[ 15.351220] Uniform CD-ROM driver Revision: 3.20
[ 15.351444] sr 0:0:1:0: Attached scsi CD-ROM sr0
[ 15.356275] sr 0:0:1:0: Attached scsi generic sg0 type 5
[ 15.388332] usb usb1: configuration #1 chosen from 1 choice
[ 15.388360] hub 1-0:1.0: USB hub found
[ 15.388370] hub 1-0:1.0: 3 ports detected
[ 15.490155] ACPI: PCI Interrupt 0000:00:03.1 -> GSI 21 (level, low) -> IRQ 18
[ 15.490170] ohci_hcd 0000:00:03.1: OHCI Host Controller
[ 15.490193] ohci_hcd 0000:00:03.1: new USB bus registered, assigned bus number 2
[ 15.490210] ohci_hcd 0000:00:03.1: irq 18, io mem 0xfeafe000
[ 15.548049] usb usb2: configuration #1 chosen from 1 choice
[ 15.548077] hub 2-0:1.0: USB hub found
[ 15.548086] hub 2-0:1.0: 3 ports detected
[ 15.649916] ACPI: PCI Interrupt 0000:00:03.2[C] -> GSI 22 (level, low) -> IRQ 19
[ 15.649931] ohci_hcd 0000:00:03.2: OHCI Host Controller
[ 15.649958] ohci_hcd 0000:00:03.2: new USB bus registered, assigned bus number 3
[ 15.649973] ohci_hcd 0000:00:03.2: irq 19, io mem 0xfeafd000
[ 15.707778] usb usb3: configuration #1 chosen from 1 choice
[ 15.707804] hub 3-0:1.0: USB hub found
[ 15.707814] hub 3-0:1.0: 2 ports detected
[ 15.810112] ACPI: PCI Interrupt 0000:00:03.3[D] -> GSI 23 (level, low) -> IRQ 20
[ 15.810126] ehci_hcd 0000:00:03.3: EHCI Host Controller
[ 15.810158] ehci_hcd 0000:00:03.3: new USB bus registered, assigned bus number 4
[ 15.810191] PCI: cache line size of 64 is not supported by device 0000:00:03.3
[ 15.810202] ehci_hcd 0000:00:03.3: irq 20, io mem 0xfeafc000
[ 15.953347] usb 2-1: new full speed USB device using ohci_hcd and address 2
[ 15.953367] ehci_hcd 0000:00:03.3: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
[ 15.953471] usb usb4: configuration #1 chosen from 1 choice
[ 15.953497] hub 4-0:1.0: USB hub found
[ 15.953505] hub 4-0:1.0: 8 ports detected
[ 16.057366] sata_sis 0000:00:05.0: version 0.8
[ 16.057388] ACPI: PCI Interrupt 0000:00:05.0[A] -> GSI 17 (level, low) -> IRQ 21
[ 16.057395] sata_sis 0000:00:05.0: Detected SiS 182/965L chipset
[ 16.057468] scsi2 : sata_sis
[ 16.057506] scsi3 : sata_sis
[ 16.057585] ata3: SATA max UDMA/133 cmd 0x0001c800 ctl 0x0001c402 bmdma 0x0001b400 irq 21
[ 16.057591] ata4: SATA max UDMA/133 cmd 0x0001c000 ctl 0x0001b802 bmdma 0x0001b408 irq 21
[ 16.524468] ata3: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 16.573561] ata3.00: ATA-7: ST3500630AS, 3.AAK, max UDMA/133
[ 16.573566] ata3.00: 976773168 sectors, multi 16: LBA48 NCQ (depth 0/32)
[ 16.640086] ata3.00: configured for UDMA/133
[ 16.688203] usb 2-1: new full speed USB device using ohci_hcd and address 3
[ 16.902978] usb 2-1: configuration #1 chosen from 1 choice
[ 16.917751] usbcore: registered new interface driver libusual
[ 16.924316] Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
[ 16.924322] ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
[ 16.927016] Initializing USB Mass Storage driver...
[ 16.927078] scsi4 : SCSI emulation for USB Mass Storage devices
[ 16.927122] usb-storage: device found at 3
[ 16.927124] usb-storage: waiting for device to settle before scanning
[ 16.927137] usbcore: registered new interface driver usb-storage
[ 16.927139] USB Mass Storage support registered.
[ 17.103577] ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 17.143183] ata4.00: ATA-7: ST340211AS, 3.AAE, max UDMA/133
[ 17.143186] ata4.00: 78165360 sectors, multi 16: LBA48 NCQ (depth 0/32)
[ 17.209725] ata4.00: configured for UDMA/133
[ 17.209827] scsi 2:0:0:0: Direct-Access ATA ST3500630AS 3.a PQ: 0 ANSI: 5
[ 17.209886] scsi 2:0:0:0: Attached scsi generic sg1 type 0
[ 17.210365] scsi 3:0:0:0: Direct-Access ATA ST340211AS 3.a PQ: 0 ANSI: 5
[ 17.210420] scsi 3:0:0:0: Attached scsi generic sg2 type 0
[ 17.222957] sd 2:0:0:0: [sda] 976773168 512-byte hardware sectors (500108 MB)
[ 17.222971] sd 2:0:0:0: [sda] Write Protect is off
[ 17.222974] sd 2:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 17.222989] sd 2:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 17.223040] sd 2:0:0:0: [sda] 976773168 512-byte hardware sectors (500108 MB)
[ 17.223049] sd 2:0:0:0: [sda] Write Protect is off
[ 17.223052] sd 2:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 17.223065] sd 2:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 17.223070] sda: sda1 sda2 < sda5 >
[ 17.261491] sd 2:0:0:0: [sda] Attached SCSI disk
[ 17.261671] sd 3:0:0:0: [sdb] 78165360 512-byte hardware sectors (40021 MB)
[ 17.261683] sd 3:0:0:0: [sdb] Write Protect is off
[ 17.261686] sd 3:0:0:0: [sdb] Mode Sense: 00 3a 00 00
[ 17.261700] sd 3:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 17.261742] sd 3:0:0:0: [sdb] 78165360 512-byte hardware sectors (40021 MB)
[ 17.261751] sd 3:0:0:0: [sdb] Write Protect is off
[ 17.261754] sd 3:0:0:0: [sdb] Mode Sense: 00 3a 00 00
[ 17.261767] sd 3:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 17.261770] sdb: [LDM] sdb1
[ 17.341898] sd 3:0:0:0: [sdb] Attached SCSI disk
[ 17.617401] Attempting manual resume
[ 17.617405] swsusp: Resume From Partition 8:5
[ 17.617407] PM: Checking swsusp image.
[ 17.617592] PM: Resume from disk failed.
[ 17.653726] kjournald starting. Commit interval 5 seconds
[ 17.653738] EXT3-fs: mounted filesystem with ordered data mode.
[ 21.917244] usb-storage: device scan complete
[ 21.925244] scsi 4:0:0:0: Direct-Access USB DISK 2.08 PQ: 0 ANSI: 0 CCS
[ 21.957171] sd 4:0:0:0: [sdc] 64000 512-byte hardware sectors (33 MB)
[ 21.963232] sd 4:0:0:0: [sdc] Write Protect is off
[ 21.963237] sd 4:0:0:0: [sdc] Mode Sense: 43 00 00 00
[ 21.963240] sd 4:0:0:0: [sdc] Assuming drive cache: write through
[ 21.989786] sd 4:0:0:0: [sdc] 64000 512-byte hardware sectors (33 MB)
[ 21.997112] sd 4:0:0:0: [sdc] Write Protect is off
[ 21.997117] sd 4:0:0:0: [sdc] Mode Sense: 43 00 00 00
[ 21.997120] sd 4:0:0:0: [sdc] Assuming drive cache: write through
[ 21.997126] sdc: sdc1
[ 22.008150] sd 4:0:0:0: [sdc] Attached SCSI removable disk
[ 22.008192] sd 4:0:0:0: Attached scsi generic sg3 type 0
[ 23.851864] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[ 23.859088] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
[ 24.292797] Silan SC92031 PCI Fast Ethernet Adapter driver 2.0c
[ 24.292848] ACPI: PCI Interrupt 0000:00:09.0[A] -> GSI 17 (level, low) -> IRQ 21
[ 24.775799] sis190 Gigabit Ethernet driver 1.2 loaded.
[ 24.775823] ACPI: PCI Interrupt 0000:00:04.0[A] -> GSI 19 (level, low) -> IRQ 22
[ 24.775835] PCI: Setting latency timer of device 0000:00:04.0 to 64
[ 24.827272] 0000:00:04.0: Read MAC address from APC.
[ 24.855623] 0000:00:04.0: Broadcom PHY AC131 transceiver at address 0.
[ 25.377505] input: PC Speaker as /class/input/input2
[ 25.446841] 0000:00:04.0: SiS 190 PCI Fast Ethernet adapter at f8968c00 (IRQ: 22), 00:19:21:9b:97:6a
[ 25.446846] eth1: GMII mode.
[ 25.446851] eth1: Enabling Auto-negotiation.
[ 25.647350] input: ImPS/2 Generic Wheel Mouse as /class/input/input3
[ 25.650111] parport_pc 00:09: reported by Plug and Play ACPI
[ 25.650179] parport0: PC-style at 0x378 (0x778), irq 7, dma 3 [PCSPP,TRISTATE,COMPAT,ECP,DMA]
[ 25.708664] ACPI: PCI Interrupt 0000:00:02.7[C] -> GSI 18 (level, low) -> IRQ 23
[ 26.029816] intel8x0_measure_ac97_clock: measured 54907 usecs
[ 26.029820] intel8x0: clocking to 48000
[ 55.925274] lp0: using parport0 (interrupt-driven).
[ 55.964626] Adding 4554388k swap on /dev/sda5. Priority:-1 extents:1 across:4554388k
[ 56.397587] EXT3 FS on sda1, internal journal
[ 57.492226] No dock devices found.
[ 57.622322] input: Power Button (FF) as /class/input/input4
[ 57.627165] ACPI: Power Button (FF) [PWRF]
[ 57.667971] input: Power Button (CM) as /class/input/input5
[ 57.672759] ACPI: Power Button (CM) [PWRB]
[ 57.913518] powernow-k8: Power state transitions not supported
[ 59.412852] ppdev: user-space parallel port driver
[ 59.485289] audit(1195059840.648:3): type=1503 operation="inode_permission" requested_mask="a" denied_mask="a" name="/dev/tty" pid=4833 profile="/usr/sbin/cupsd"
[ 59.523726] apm: BIOS not found.
[ 59.708388] Failure registering capabilities with primary security module.
[ 59.863814] Bluetooth: Core ver 2.11
[ 59.864138] NET: Registered protocol family 31
[ 59.864141] Bluetooth: HCI device and connection manager initialized
[ 59.864145] Bluetooth: HCI socket layer initialized
[ 59.882873] Bluetooth: L2CAP ver 2.8
[ 59.882878] Bluetooth: L2CAP socket layer initialized
[ 59.974547] Bluetooth: RFCOMM socket layer initialized
[ 59.974877] Bluetooth: RFCOMM TTY layer initialized
[ 59.974880] Bluetooth: RFCOMM ver 1.8
[ 69.323164] eth1_rename: PHY reset until link up.
[ 79.339742] eth1_rename: PHY reset until link up.
[ 89.356336] eth1_rename: PHY reset until link up.
[ 99.372917] eth1_rename: PHY reset until link up.
[ 109.389491] eth1_rename: PHY reset until link up.
[ 119.406068] eth1_rename: PHY reset until link up.
[ 129.422644] eth1_rename: PHY reset until link up.
[ 139.439220] eth1_rename: PHY reset until link up.
[ 149.455801] eth1_rename: PHY reset until link up.
[ 159.472380] eth1_rename: PHY reset until link up.
[ 169.488959] eth1_rename: PHY reset until link up.
[ 179.505542] eth1_rename: PHY reset until link up.
[ 189.522117] eth1_rename: PHY reset until link up.
[ 199.538697] eth1_rename: PHY reset until link up.
[ 209.555288] eth1_rename: PHY reset until link up.
[ 219.571856] eth1_rename: PHY reset until link up.
[ 229.588436] eth1_rename: PHY reset until link up.
[ 239.605016] eth1_rename: PHY reset until link up.
[ 249.621595] eth1_rename: PHY reset until link up.
[ 262.793317] eth1_rename: PHY reset until link up.
[ 272.809907] eth1_rename: PHY reset until link up.
[ 282.826476] eth1_rename: PHY reset until link up.
[ 290.708612] eth0: link down
[ 291.896250] NET: Registered protocol family 17
[ 292.337042] eth0: link up, 100Mbps, full-duplex
[ 293.716931] NET: Registered protocol family 10
[ 293.717173] lo: Disabled Privacy Extensions
[ 293.717428] ADDRCONF(NETDEV_UP): eth1_rename: link is not ready
[ 295.643781] ADDRCONF(NETDEV_UP): eth1_rename: link is not ready
[ 303.882060] eth0: no IPv6 routers present
[ 305.635367] eth1_rename: PHY reset until link up.
[ 310.085560] ADDRCONF(NETDEV_UP): eth1_rename: link is not ready
[ 320.077131] eth1_rename: PHY reset until link up.
[ 330.093709] eth1_rename: PHY reset until link up.
[ 340.110288] eth1_rename: PHY reset until link up.
[ 350.126875] eth1_rename: PHY reset until link up.
[ 360.143446] eth1_rename: PHY reset until link up.
[ 370.160027] eth1_rename: PHY reset until link up.
[ 380.176606] eth1_rename: PHY reset until link up.
[ 390.193207] eth1_rename: PHY reset until link up.
[ 400.209765] eth1_rename: PHY reset until link up.
[ 410.226344] eth1_rename: PHY reset until link up.
[ 420.242924] eth1_rename: PHY reset until link up.
[ 430.259504] eth1_rename: PHY reset until link up.
[ 440.276084] eth1_rename: PHY reset until link up.
lspci
00:00.0 Host bridge: Silicon Integrated Systems [SiS] 761/M761 Host (rev 01)
00:01.0 PCI bridge: Silicon Integrated Systems [SiS] PCI-to-PCI bridge
00:02.0 ISA bridge: Silicon Integrated Systems [SiS] SiS965 [MuTIOL Media IO] (rev 48)
00:02.5 IDE interface: Silicon Integrated Systems [SiS] 5513 [IDE] (rev 01)
00:02.7 Multimedia audio controller: Silicon Integrated Systems [SiS] AC'97 Sound Controller (rev a0)
00:03.0 USB Controller: Silicon Integrated Systems [SiS] USB 1.0 Controller (rev 0f)
00:03.1 USB Controller: Silicon Integrated Systems [SiS] USB 1.0 Controller (rev 0f)
00:03.2 USB Controller: Silicon Integrated Systems [SiS] USB 1.0 Controller (rev 0f)
00:03.3 USB Controller: Silicon Integrated Systems [SiS] USB 2.0 Controller
00:04.0 Ethernet controller: Silicon Integrated Systems [SiS] 190 Gigabit Ethernet Adapter
00:05.0 IDE interface: Silicon Integrated Systems [SiS] 182 SATA/RAID Controller (rev 01)
00:06.0 PCI bridge: Silicon Integrated Systems [SiS] PCI-to-PCI bridge
00:07.0 PCI bridge: Silicon Integrated Systems [SiS] PCI-to-PCI bridge
00:09.0 Ethernet controller: Hangzhou Silan Microelectronics Co., Ltd. RTL8139D [Realtek] PCI 10/100BaseTX ethernet adaptor (rev 01)
00:18.0 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] HyperTransport Technology Configuration
00:18.1 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Address Map
00:18.2 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] DRAM Controller
00:18.3 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Miscellaneous Control
01:00.0 VGA compatible controller: ATI Technologies Inc Unknown device 94c3
01:00.1 Audio device: ATI Technologies Inc Unknown device aa10

boi · 14 de Novembro de 2007, 15:51

Placas Sis são problemáticas no Linux, se bem que eu tinha uma placa Pcchips com rede Sis190 que funcionava normalmente. Mas essa Realtek deveria funcionar. Experimente desabilitar a onboard pelo setup da BIOS. Se mesmo assim não funcionar, é quase certo que é um problema de configuração, não de hardware.

edublind · 16 de Novembro de 2007, 11:55

Poie è eu desabilitei a placa omboard na bios mas infelizmente ão funcionou.

kra esse problema desanima.
Help MEEEEEEEEEEEEEEEEEEEEEEE
Grato

boi · 16 de Novembro de 2007, 14:09

Então acho que podemos eliminar o problema de hardware. O que tem que ser visto agora é como foi feita a configuração de internet. Como é feita a autenticação com esses provedores? É por pppoe, dhcp? Seria necessário dar mais detalhes.

edublind · 19 de Novembro de 2007, 10:27

Então
os 2 links que tenho aqui virtua e ajato estão configurados no roteador ou seja a net ta passando direto rpas maquinas liberada já
o que é mais estranho é que quando eu coloco o live cd em qualquer maquina da empresa navego normalmente na net mas quando coloco nessa aqui a coisa trava

pior que tenho 2 maquinas iguais não tem como ficar sem elas

edublind · 19 de Novembro de 2007, 11:18

Então descobri algo que talvez possa ajudar
desabilitei o ipv6 na maquina e agora só consigo entrar em sites do dominio do google
orkut gmail google
e isso só funciona quando na configuração da placa de rede eu coloco em modo roaming
resultado do ifconfig

site do ndiswrapper.
Para instalar o ndiswrapper, instale o pacote ndiswrapper-utils:
sudo apt-get install ndiswrapper-utils
Este pacote é fornecido no CD do Ubuntu. Se você tiver acesso à internet, você pode também opcionalmente instalar uma ferramenta gráfica chamada ndisgtk do repositório Universe (veja Adicionando Repositorios).
sudo apt-get install ndisgtk
Instalando o Driver
De modo a configurar o ndiswrapper, é necessário obter o driver Windows para a sua placa de rede sem fios. Geralmente, a melhor maneira de se fazer isto é através do CD fornecido com a sua placa de rede. Você deve copiar dois arquivos para o mesmo local no seu computador, um cujo nome termina com a extensão .SYS e outro com a extensão .INF. Se você encontrar arquivos cujo os nomes terminem com .BIN, copie estes também.
Se você não conseguir encontrar os arquivos corretos e possuir acesso alternativo à internet, você poderá encontrar mais ajuda no site do ndiswrapper.
Se você tem instalada a ferramenta gráfica ndisgtk, para configurar o ndiswrapper, selecione o menu Sistema -> Administração -> Drivers Windows para Placas de Rede Sem Fios e siga as instruções fornecidas.
Se você não instalou a ferramenta gráfica, use este procedimento:
1. Abra o terminal e digite o comando:
sudo ndiswrapper -i ~/Desktop/drivername.inf
O comando acima assume que o seu arquivo .INF tem o nome drivername.inf e que foi copiado para o seu Desktop. Substitua estes valores se necessário.
2. Para verificar se está funcionando corretamente, digite:
ndiswrapper -l
Se estiver funcionando corretamente, você deve visualizar:
Installed ndis drivers:
{name of driver} driver present, hardware present
3. Para o ndiswrapper funcionar, você necessita carregar um módulo. Para fazer isto, digite:
sudo depmod -a
sudo modprobe ndiswrapper
4. Para assegurar que o módulo seja carregado cada vez o computador for inicializado, digite:
sudo ndiswrapper -m
Pronto! Agora deve ser possível conectar-se à internet. Veja o próximo passo:
Para placas detectadas
Network Manager
Instalação
sudo apt-get install network-manager-gnome
Usando o NetworkManager

O network-manager-gnome procura automaticamente por redes disponíveis e para conectar-se em uma é muito simples. Primeiramente, selecione-a com o botão esquerdo do mouse e em seguida informe a senha que será solicitada, caso a rede esteja protegida (WEP ou WPA). Existe também a opção de armazenar está senha no chaveiro, siga as instruções fornecidas se desejável. Após conectado, detalhes sobre a conexão e potência do sinal também são exibidos e ficam residentes ao lado do relógio.

Resolvendo Problemas
Algumas placas podem não funcionar automaticamente no Ubuntu. Se este for o caso, por favor veja o Guia de Redes Sem Fios, o qual é uma excelente fonte para resolver problemas com placas de rede sem fios.
Uma lista completa das placas de rede sem fios que funcionam no Ubuntu pode ser encontrada no wiki internacional. Por favor, adicione a sua placa à lista se ela funcionar.
Todas as informações relacionadas à redes sem fios no Ubuntu é colecionada na Central de Redes Sem Fios no wiki internacional.
Em alguns fóruns vi notícias com problemas na rede devido ao ipv6 estar ativo por padrão, para mudar isso então faça o seguinte:
Em terminal:
sudo vim /etc/modprobe.d/aliases
Em modo gráfico, Alt + F2 e digite:
gksu gedit /etc/modprobe.d/aliases
Muda a linha de:
alias net-pf-10 ipv6
para
alias net-pf-10 off

Retorno do ifconfig

eth0 Encapsulamento do Link: Ethernet Endereço de HW 00:19:21:9B:97:6A
inet end.: 192.168.0.84 Bcast:192.168.0.255 Masc:255.255.255.0
UP BROADCAST RUNNING MULTICAST MTU:1500 Métrica:1
pacotes RX:692 erros:15 descartados:0 excesso:0 quadro:15
Pacotes TX:597 erros:0 descartados:0 excesso:0 portadora:0
colisões:0 txqueuelen:1000
RX bytes:901659 (880.5 KB) TX bytes:55462 (54.1 KB)
IRQ:22 Endereço de E/S:0xdead

lo Encapsulamento do Link: Loopback Local
inet end.: 127.0.0.1 Masc:255.0.0.0
UP LOOPBACK RUNNING MTU:16436 Métrica:1
pacotes RX:16 erros:0 descartados:0 excesso:0 quadro:0
Pacotes TX:16 erros:0 descartados:0 excesso:0 portadora:0
colisões:0 txqueuelen:0
RX bytes:1408 (1.3 KB) TX bytes:1408 (1.3 KB)
Vlw pela ajuda ai galera espero que possam me ajudar

boi · 19 de Novembro de 2007, 21:58

A minha antiga PCchips tinha um problema parecido. A máquina às conectava mas não navegava. Aliás, até navegava, mas só conseguia acessar o Google. Nunca descobri o que causava o problema, mas achei uma forma de não acontecer. Nessa máquina eu tinha um boot duplo, Windows e Linux. Se eu ligava a máquina e entrava diretamente no Linux, tudo bem. Mas se eu ia para o Windows e depois dava um reboot, indo para o Linux, acontecia esse problema de não conseguir acessar nenhum site, a não ser o Google. Eu precisa desligar tudo, inclusive o modem, e religar, indo direto para o Linux.

Minha placa de rede não funciona Sis190

boi

boi

boi