PixelView PlayTV Pro Ultra

[tuxvader]

Por incrível que pareça, mesmo seguindo as dicas aki do fórum, ainda não consigo fazer funcionar minha placa de captura acima no Ubuntu 7.04...

Aí vai o dmesg pra ver se alguém tem uma luz:

34.576276] cx2388x v4l2 driver version 0.0.6 loaded
[   34.576710] ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 18
[   34.576719] ACPI: PCI Interrupt 0000:02:08.0[A] -> Link [LNKC] -> GSI 18 (level, low) -> IRQ 20
[   34.576766] CORE cx88[0]: subsystem: 0000:0000, board: PixelView PlayTV Ultra Pro (Stereo) [card=27,insmod option]
[   34.576770] TV tuner 1 at 0x1fe, Radio tuner -1 at 0x1fe
[   34.699391] tveeprom 2-0050: Huh, no eeprom present (err=-121)?
[   34.699461] input: cx88 IR (PixelView PlayTV Ultra as /class/input/input4
[   34.699499] cx88[0]/0: found at 0000:02:08.0, rev: 5, irq: 20, latency: 64, mmio: 0xfd000000
[   34.709214] ACPI: PCI Interrupt Link [LAUI] enabled at IRQ 20
[   34.709219] ACPI: PCI Interrupt 0000:00:06.0[A] -> Link [LAUI] -> GSI 20 (level, low) -> IRQ 18
[   34.709242] PCI: Setting latency timer of device 0000:00:06.0 to 64
[   34.727482] tuner 2-0061: chip found @ 0xc2 (cx88[0])
[   34.727509] tuner 2-0061: type set to 1 (Philips PAL_I (FI1246 and compatibles))
[   34.727514] tuner 2-0061: type set to 1 (Philips PAL_I (FI1246 and compatibles))
[   34.728446] tuner 2-0063: chip found @ 0xc6 (cx88[0])
[   34.737585] cx88[0]/0: registered device video0 [v4l2]
[   34.737611] cx88[0]/0: registered device vbi0
[   34.737659] cx88[0]/0: registered device radio0
[   35.029327] intel8x0_measure_ac97_clock: measured 58705 usecs
[   35.029332] intel8x0: clocking to 46964
[   35.211586] fuse init (API version 7.
[   35.240299] lp0: using parport0 (interrupt-driven).
[   35.431119] Adding 265032k swap on /dev/disk/by-uuid/077847a3-c4bd-482e-970f-13fd520b8250.  Priority:-1 extents:1 across:265032k
[   35.646526] EXT3 FS on sda3, internal journal
[   35.745450] NET: Registered protocol family 10
[   35.745545] lo: Disabled Privacy Extensions
[   36.317531] kjournald starting.  Commit interval 5 seconds
[   36.317701] EXT3 FS on sda1, internal journal
[   36.317706] EXT3-fs: mounted filesystem with ordered data mode.
[   36.351865] NTFS driver 2.1.28 [Flags: R/O MODULE].
[   36.400462] NTFS volume version 3.1.
[   36.430108] kjournald starting.  Commit interval 5 seconds
[   36.430278] EXT3 FS on sda6, internal journal
[   36.430283] EXT3-fs: mounted filesystem with ordered data mode.
[   36.461477] kjournald starting.  Commit interval 5 seconds
[   36.461653] EXT3 FS on sda7, internal journal
[   36.461657] EXT3-fs: mounted filesystem with ordered data mode.
[   36.484707] kjournald starting.  Commit interval 5 seconds
[   36.484881] EXT3 FS on sda8, internal journal
[   36.484885] EXT3-fs: mounted filesystem with ordered data mode.
[   41.945178] No dock devices found.
[   41.999624] ibm_acpi: ec object not found
[   42.031070] Using specific hotkey driver
[   42.240498] input: Power Button (FF) as /class/input/input5
[   42.245572] ACPI: Power Button (FF) [PWRF]
[   42.284197] input: Power Button (CM) as /class/input/input6
[   42.289296] ACPI: Power Button (CM) [PWRB]
[   42.303040] pcc_acpi: loading...
[   42.560405] powernow-k8: Power state transitions not supported
[   45.374293] agpgart: Found an AGP 3.0 compliant device at 0000:00:00.0.
[   45.374688] agpgart: Putting AGP V3 device at 0000:00:00.0 into 8x mode
[   45.374996] agpgart: Putting AGP V3 device at 0000:01:00.0 into 8x mode
[   46.243573] ppdev: user-space parallel port driver
[   47.036416] apm: BIOS version 1.2 Flags 0x03 (Driver version 1.16ac)
[   47.036421] apm: overridden by ACPI.
[   48.839227] /dev/vmmon[5095]: Module vmmon: registered with major=10 minor=165
[   48.839626] /dev/vmmon[5095]: Module vmmon: initialized
[   48.998420] /dev/vmnet: open called by PID 5142 (vmnet-bridge)
[   48.998798] /dev/vmnet: hub 0 does not exist, allocating memory.
[   48.999081] /dev/vmnet: port on hub 0 successfully opened
[   48.999338] bridge-eth0: enabling the bridge
[   48.999552] bridge-eth0: up
[   48.999721] bridge-eth0: already up
[   48.999912] bridge-eth0: attached
[   49.108521] /dev/vmnet: open called by PID 5158 (vmnet-natd)
[   49.108848] /dev/vmnet: hub 8 does not exist, allocating memory.
[   49.109120] /dev/vmnet: port on hub 8 successfully opened
[   49.120221] /dev/vmnet: open called by PID 5149 (vmnet-netifup)
[   49.120567] /dev/vmnet: hub 1 does not exist, allocating memory.
[   49.120838] /dev/vmnet: port on hub 1 successfully opened
[   49.502121] /dev/vmnet: open called by PID 5174 (vmnet-dhcpd)
[   49.502417] /dev/vmnet: port on hub 1 successfully opened
[   49.764150] Bluetooth: Core ver 2.11
[   49.764515] NET: Registered protocol family 31
[   49.764518] Bluetooth: HCI device and connection manager initialized
[   49.764523] Bluetooth: HCI socket layer initialized
[   49.981616] Bluetooth: L2CAP ver 2.8
[   49.981620] Bluetooth: L2CAP socket layer initialized
[   50.064287] /dev/vmnet: open called by PID 5241 (vmnet-netifup)
[   50.064485] /dev/vmnet: port on hub 8 successfully opened
[   50.129948] Bluetooth: RFCOMM socket layer initialized
[   50.129962] Bluetooth: RFCOMM TTY layer initialized
[   50.129964] Bluetooth: RFCOMM ver 1.8
[   50.635574] /dev/vmnet: open called by PID 5252 (vmnet-dhcpd)
[   50.635866] /dev/vmnet: port on hub 8 successfully opened
[   58.821484] eth0: no IPv6 routers present
[   59.288860] vmnet1: no IPv6 routers present
[   61.002579] vmnet8: no IPv6 routers present
[ 1064.282044] cx88[0]: video y / packed - dma channel status dump
[ 1064.282051] cx88[0]:   cmds: initial risc: 0x2a6da000
[ 1064.282055] cx88[0]:   cmds: cdt base    : 0x00180440
[ 1064.282058] cx88[0]:   cmds: cdt size    : 0x0000000c
[ 1064.282061] cx88[0]:   cmds: iq base     : 0x00180400
[ 1064.282064] cx88[0]:   cmds: iq size     : 0x00000010
[ 1064.282067] cx88[0]:   cmds: risc pc     : 0x2aabea48
[ 1064.282071] cx88[0]:   cmds: iq wr ptr   : 0x00000101
[ 1064.282074] cx88[0]:   cmds: iq rd ptr   : 0x00000105
[ 1064.282077] cx88[0]:   cmds: cdt current : 0x00000458
[ 1064.282080] cx88[0]:   cmds: pci target  : 0x20ef5660
[ 1064.282083] cx88[0]:   cmds: line / byte : 0x00f00000
[ 1064.282086] cx88[0]:   risc0: 0x80008200 [ sync resync count=512 ]
[ 1064.282091] cx88[0]:   risc1: 0x1c0005a0 [ write sol eol count=1440 ]
[ 1064.282096] cx88[0]:   risc2: 0x20e0b5a0 [ skip 23 22 21 resync 13 12 count=1440 ]
[ 1064.282102] cx88[0]:   risc3: 0x1c0005a0 [ write sol eol count=1440 ]
[ 1064.282107] cx88[0]:   iq 0: 0x20e0e2a0 [ skip 23 22 21 resync 14 13 count=672 ]
[ 1064.282113] cx88[0]:   iq 1: 0x20ef4580 [ skip 23 22 21 19 18 cnt1 cnt0 14 count=1408 ]
[ 1064.282119] cx88[0]:   iq 2: 0x1c0005a0 [ write sol eol count=1440 ]
[ 1064.282124] cx88[0]:   iq 3: 0x20ef50c0 [ arg #1 ]
[ 1064.282127] cx88[0]:   iq 4: 0x80008200 [ sync resync count=512 ]
[ 1064.282131] cx88[0]:   iq 5: 0x1c0005a0 [ write sol eol count=1440 ]
[ 1064.282137] cx88[0]:   iq 6: 0x20e0b5a0 [ arg #1 ]
[ 1064.282139] cx88[0]:   iq 7: 0x1c0005a0 [ write sol eol count=1440 ]
[ 1064.282145] cx88[0]:   iq 8: 0x20e0c0e0 [ arg #1 ]
[ 1064.282147] cx88[0]:   iq 9: 0x180003e0 [ write sol count=992 ]
[ 1064.282152] cx88[0]:   iq a: 0x20e0cc20 [ arg #1 ]
[ 1064.282155] cx88[0]:   iq b: 0x140001c0 [ write eol count=448 ]
[ 1064.282160] cx88[0]:   iq c: 0x20e0d000 [ arg #1 ]
[ 1064.282162] cx88[0]:   iq d: 0x1c0005a0 [ write sol eol count=1440 ]
[ 1064.282168] cx88[0]:   iq e: 0x20e0d760 [ arg #1 ]
[ 1064.282170] cx88[0]:   iq f: 0x1c0005a0 [ write sol eol count=1440 ]
[ 1064.282175] cx88[0]:   iq 10: 0x00180c00 [ arg #1 ]
[ 1064.282178] cx88[0]: fifo: 0x00180c00 -> 0x183400
[ 1064.282180] cx88[0]: ctrl: 0x00180400 -> 0x180460
[ 1064.282183] cx88[0]:   ptr1_reg: 0x00181ce0
[ 1064.282186] cx88[0]:   ptr2_reg: 0x00180478
[ 1064.282189] cx88[0]:   cnt1_reg: 0x00000000
[ 1064.282191] cx88[0]:   cnt2_reg: 0x00000000
[ 1064.282198] cx88[0]/0: [ee0f87c0/3] timeout - dma=0x2aabe000

Alguém?

[Chaintech]

Por exemplo, se a placa possui chip bttv como as desta lista:
http://www.linuxtv.org/v4lwiki/index.php/Cardlist.BTTV

E o Tuner tbm:
http://linuxtv.org/hg/v4l-dvb?cmd=fi...e=-1;style=raw

Vou dar o exemplo da minha placa que é uma Leadtek WinFast 2000 XP, é a placa nº 34 e o tuner é o nº 41 na lista acima, apenas adiciono 3 linhas no arquivo rc.local.

EDITAR RC.LOCAL QUE ESTA EM /ETC/INIT.D
Adicionar no Final:
rmmod bt878
rmmod bttv
modprobe bttv card=34 tuner=41

Reinicio o sistema e instalo o software tvtime pra assistir.

Isto vale para o Debian,Ubuntu,Fedora,Gentoo, testei em todos eles e a solução é a mesma.

Agora se for uma placa que não tenha driver no kernel, dai realmente fica complicado...

Abraços.

[mstr]

Adicione no "/etc/modules" as linhas:

#PlayTV Pro Ultra
modprobe -r cx8800
modprobe -r cx88xx
modprobe -r tuner
modprobe cx88xx card=27 tuner=38 i2c_scan=1 radio=1
modprobe cx8800

reinicie e boa sorte