Aí pessoal, beem preciso, fiquei animadasso pra tentar arrumar, mas nao deu certo. Editei o interfaces como vc disse, zekkerj, mas não deu. Fiquei na dúvida entre qual eram as linhas realmente referentes ao pppoe,
auto lo
iface lo inet loopback
auto dsl-provider
iface dsl-provider inet ppp
pre-up /sbin/ifconfig eth0 up # line maintained by pppoeconf
provider dsl-provider
auto eth0
iface eth0 inet (aqui tinha outra coisa diferente de dhcp, ms esqueci)
comentei a terceira grandona, nao deu, comentei todas nao deu também (isso reiniciando a cada vez).
Acho que o problema maior é que ele não tá mais reconhecendo o cabo. Vc liga, desliga, e nao acontece nada. Antes, mesmo que nao funcionasse, pelo menos vc via ele tentando localizar a rede, no sinalzinho de carregando na barra, ou mostrava lá "vc tá conectado" ou "vc nao tá mais desconectado".
Uma coisa que eu acho que deve contar, é que, pelo que eu me lembre, antes de configurar o adsl, a conexao que existia se chamava apenas eth0. Agora esta la: ifupdown (eth0).
eu vi vc comentando um post sobre ativar placas de rede, achei mto massa, ms nao sei se é esse caso, pq no meu aparece a placa, além daquela lo.
bom... n sei o que mais pode esclarecer... (leigo total). ms de qlquer forma vai o resultado daqules comandos
root@xxxxx:/home/icaro# lspci
00:00.0 Host bridge: ATI Technologies Inc RS690 Host Bridge
00:01.0 PCI bridge: ATI Technologies Inc RS690 PCI to PCI Bridge (Internal gfx)
00:06.0 PCI bridge: ATI Technologies Inc RS690 PCI to PCI Bridge (PCI Express Port 2)
00:07.0 PCI bridge: ATI Technologies Inc RS690 PCI to PCI Bridge (PCI Express Port 3)
00:12.0 SATA controller: ATI Technologies Inc SB600 Non-Raid-5 SATA
00:13.0 USB Controller: ATI Technologies Inc SB600 USB (OHCI0)
00:13.1 USB Controller: ATI Technologies Inc SB600 USB (OHCI1)
00:13.4 USB Controller: ATI Technologies Inc SB600 USB (OHCI4)
00:13.5 USB Controller: ATI Technologies Inc SB600 USB Controller (EHCI)
00:14.0 SMBus: ATI Technologies Inc SBx00 SMBus Controller (rev 14)
00:14.1 IDE interface: ATI Technologies Inc SB600 IDE
00:14.2 Audio device: ATI Technologies Inc SBx00 Azalia (Intel HDA)
00:14.3 ISA bridge: ATI Technologies Inc SB600 PCI to LPC Bridge
00:14.4 PCI bridge: ATI Technologies Inc SBx00 PCI to PCI Bridge
00:18.0 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] HyperTransport Technology Configuration
00:18.1 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Address Map
00:18.2 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] DRAM Controller
00:18.3 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Miscellaneous Control
01:05.0 VGA compatible controller: ATI Technologies Inc RS690M [Radeon X1200 Series]
02:00.0 Network controller: Broadcom Corporation BCM4312 802.11b/g (rev 01)
05:00.0 Ethernet controller: Attansic Technology Corp. Atheros AR8132 / L1c Gigabit Ethernet Adapter (rev c0)
root@xxxxx:/home/icaro# lsusb
Bus 002 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 001 Device 002: ID 064e:a103 Suyin Corp.
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
root@xxxxx:/home/icaro# ifconfig
lo Link encap:Loopback Local
inet end.: 127.0.0.1 Masc:255.0.0.0
endereço inet6: ::1/128 Escopo:Máquina
UP LOOPBACK RUNNING MTU:16436 Métrica:1
pacotes RX:4 erros:0 descartados:0 excesso:0 quadro:0
Pacotes TX:4 erros:0 descartados:0 excesso:0 portadora:0
colisões:0 txqueuelen:0
RX bytes:240 (240.0 B) TX bytes:240 (240.0 B)
root@xxxxx:/home/icaro# sudo lshw -c network
*-network
description: Network controller
product: BCM4312 802.11b/g
vendor: Broadcom Corporation
physical id: 0
bus info: pci@0000:02:00.0
version: 01
width: 64 bits
clock: 33MHz
capabilities: pm msi pciexpress bus_master cap_list
configuration: driver=b43-pci-bridge latency=0
resources: irq:18 memory:f0300000-f0303fff
*-network DISABLED
description: Ethernet interface
product: Atheros AR8132 / L1c Gigabit Ethernet Adapter
vendor: Attansic Technology Corp.
physical id: 0
bus info: pci@0000:05:00.0
logical name: eth0
version: c0
serial: 00:26:22:6b:e2:a9
capacity: 100MB/s
width: 64 bits
clock: 33MHz
capabilities: pm msi pciexpress vpd bus_master cap_list ethernet physical tp 10bt 10bt-fd 100bt 100bt-fd autonegotiation
configuration: autonegotiation=on broadcast=yes driver=atl1c driverversion=1.0.0.1-NAPI firmware=N/A latency=0 link=yes multicast=yes port=twisted pair
resources: irq:19 memory:f0200000-f023ffff ioport:a000(size=128)