Instalação da PCMCIA Dlink no Ubuntu.

[konigabriel]

Olá pessoal do forum...
Sou iniciante em linux, achei que seria facil iniciar o aprendizado mas percebi que as coisas não funciona como no windows que é só clikar em proximo, proximo, proximo, aceito, concluido. kkkk

Portando minha dúvida é a seguinte:
--> Não consigo instalar o driver wireless PCMCIA do meu notebook no linux, tentei usar o ndiswrapper mas não deu certo, vejam o resultado logo abaixo:


abri o terminal e digitei isto..

*gabriel@notebook:~$ ndiswrapper -i /home/gabriel/Desktop/WinXP/GPLUS.inf
Installing gplus
Unable to create directory /etc/ndiswrapper/gplus.
Make sure you are running as root

*gabriel@notebook:~$ modprobe ndiswrapper
FATAL: Error inserting ndiswrapper (/lib/modules/2.6.12-9-386/kernel/drivers/net/ndiswrapper/ndiswrapper.ko): Operation not permitted


E ai pessoal, o que faço agora? Não faço a minima idéia e não tenho nenhuma noção de linux, portanto se alguem por favor tenha paciencia de escrever detalhadamente como se obter este meu objetivo eu ficarei muito grato.


Ass. Gabriel Konig Lara

[biohazard]

gabriel tenta assim !

Código: [Selecionar]

gabriel@notebook:~$sudo ndiswrapper -i /home/gabriel/Desktop/WinXP/GPLUS.inf

*gabriel@notebook:~$sudo  modprobe ndiswrapper


[rafasnn]

to tentando pelo ndiswrapper mas não acende o link da placa, o ubuntu tem um driver pra wireless o acx_pci mas ele dá erro, falta um arquivo no firmware pra wireless, alguém tem esse arquivo?

[4294754.524000] acx_init_module: dev_info is: TI acx_pci
[4294754.524000] acx_init_module: TI acx_pci.o: Ver 0.2.0pre8 driver initialized, waiting for cards to probe...
[4294754.533000] PCI: Enabling device 0000:02:00.0 (0000 -> 0002)
[4294754.533000] ACPI: PCI Interrupt 0000:02:00.0[A] -> Link [LNKD] -> GSI 11 (level, low) -> IRQ 11
[4294754.533000] PCI: Setting latency timer of device 0000:02:00.0 to 64
[4294754.533000] acx_probe_pci: WARNING: ACX111 support is quite experimental!
[4294754.533000] Found ACX111-based wireless network card at 0000:02:00.0, irq:11, phymem1:0x1f820000, phymem2:0x1f800000, mem1:0xdfbb4000, mem1_size:8192, mem2:0xdfd00000, mem2_size:131072
[4294754.533000] initial debug setting is 0x001b
[4294754.533000] acx_select_io_register_set: using ACX111 io resource addresses (size: 56)
[4294754.533000] hw_unavailable = 1
[4294754.533000] acx_probe_pci: TI acx_pci: Using IRQ 11
[4294754.534000] reset hw_unavailable++
[4294754.534000] acx_reset_mac: enable soft reset...
[4294754.534000] acx_reset_mac: disable soft reset and go to init mode...
[4294754.544000] Requesting firmware image 'TIACX111.BIN'
[4294754.812000] not using auto increment for firmware loading
[4294754.995000] acx_write_fw: firmware written
[4294755.196000] acx_write_fw (firmware): 0, acx_validate_fw: 0
[4294755.206000] acx_reset_dev: boot up eCPU and wait for complete...
[4294755.763000] input: PC Speaker
[4294755.770000] acx_reset_dev: Received signal that card is ready to be configured (the eCPU has woken up)
[4294755.770000] acx_reset_dev: Clean up cmd mailbox access area
[4294755.789000] reset hw_unavailable--
[4294755.789000] acx100: allocated net device wlan0, driver compiled against wireless extensions v17 and Linux 2.6.12-9-386
[4294755.789000] ******************************************
[4294755.789000] ************* acx_init_mac_1 *************
[4294755.789000] ******************************************
[4294755.789000] ==> Get the mailbox pointers from the scratch pad registers
[4294755.789000] CmdMailboxOffset = 1dd00
[4294755.789000] InfoMailboxOffset = 1de86
[4294755.789000] <== Get the mailbox pointers from the scratch pad registers
[4294755.789000] CommandParameters = [ 0xdfd1dd04 ]
[4294755.789000] InfoParameters = [ 0xdfd1de8a ]
[4294755.789000] Requesting firmware image 'RADIO16.BIN'
[4294755.856000] No firmware image was provided. Check your hotplug scripts
[4294755.856000] Reading firmware image '/lib/hotplug/firmware/RADIO16.BIN'
[4294755.856000] ERROR 2 trying to open firmware image file 'RADIO16.BIN': file not found - make sure this EXACT filename is in eXaCtLy this directory!
[4294755.856000] WARNING: no suitable radio module (RADIO16.BIN) found to load. No problem in case of a combined firmware, FATAL when using a separated firmware (base firmware / radio image).
[4294755.856000] acx111_init_packet_templates: Init max packet templates
[4294755.857000] acx111_create_dma_regions: set up acx111 queue memory configuration (queue configs + descriptors)
[4294755.858000] dump queue head (from card):
[4294755.858000] len: 24
[4294755.858000] tx_memory_block_address: 17F60
[4294755.858000] rx_memory_block_address: 11660
[4294755.858000] rx1_queue address: FA54
[4294755.858000] tx1_queue address: 100D4
[4294755.859000] get_mask 0x00004182, set_mask 0x00000000
[4294755.859000] Don't know how to get sensitivity for radio type 0x16, please try to add that!
[4294755.859000] Got sensitivity value 0
[4294755.859000] Got antenna value 0x8F
[4294755.859000] Got regulatory domain 0x10
[4294755.859000] get_mask 0x00000000, set_mask 0x00000000 - after update
[4294755.859000] new ratevector: 82 84 0b 0c 12 16 18 24 2c 30 48 60 6c
[4294755.859000] setting RXconfig to 2000:0000
[4294755.860000] Beacon length:69
[4294755.860000] hw_unavailable--
[4294755.860000] acx100: form factor 0x01 ((mini-)PCI / CardBus), radio type 0x16 (Radia), EEPROM version 0x05. Uploaded firmware 'Rev 0.1.0.11' (0x03010101).
[4294755.863000] creating /proc entry driver/acx_wlan0
[4294755.863000] creating /proc entry driver/acx_wlan0_diag
[4294755.863000] creating /proc entry driver/acx_wlan0_eeprom
[4294755.863000] creating /proc entry driver/acx_wlan0_phy
[4294755.863000] acx_probe_pci: TI acx_pci.o: Ver 0.2.0pre8 loaded successfully