O comando, sudo lshw -C network, após executar, exibe muito rápido a seguinte mensagem, USB e em seguida, SCSI, em seguida, apagão-se as mesmas e volta ao root.
O comando, ifconfig -a, exibe a seguinte mensagem:
lo Link encap: Loopback Local
inet end.: 127.0.0.1 Masc:255.0.0.0
endereço inet6: ::1/128 Escopo:Máquina:1
UP LOOPBACK RUNNING MTU:65536 Métrica:1
Pacotes RX:2404 erros:0 descartados:0 excesso:0 quadro:0
Pacotes TX:2404 erros:0 descartados:0 excesso:0 portadora:0
RX bytes:179232 (179.2 KB) TX bytes:179232 (179.2 KB)
O comando, lspci, exibe a seguinte mensagem:
00:00.0 Host bridge: Intel Corporation 4 Series Chipset DRAM Controller (rev 03)
00:02.0 VGA compatible controller: Intel Corporation 4 Series Chipset Integrated Graphics Controller (rev 03)
00:1b.0 Audio device: Intel Corporation NM10/ICH7 Family High Definition Audio Controller (rev 01)
00:1c.0 PCI bridge: Intel Corporation NM10/ICH7 Family PCI Express Port 1 (rev 01)
00:1c.1 PCI bridge: Intel Corporation NM10/ICH7 Family PCI Express Port 2 (rev 01)
00:1d.0 USB controller: Intel Corporation NM10/ICH7 Family USB UHCI Controller #1 (rev 01)
00:1d.1 USB controller: Intel Corporation NM10/ICH7 Family USB UHCI Controller #2 (rev 01)
00:1d.2 USB controller: Intel Corporation NM10/ICH7 Family USB UHCI Controller #3 (rev 01)
00:1d.3 USB controller: Intel Corporation NM10/ICH7 Family USB UHCI Controller #4 (rev 01)
00:1d.7 USB controller: Intel Corporation NM10/ICH7 Family USB2 EHCI Controller (rev 01)
00:1e.0 PCI bridge: Intel Corporation 82801 PCI Bridge (rev e1)
00:1f.0 ISA bridge: Intel Corporation 82801G/GR (ICH7 Family) LPC Interface Bridge (rev 01)
00:1f.1 IDE Interface: Intel Corporation 82801G (ICH7 Family) IDE Controller (rev 01)
00:1f.2 IDE Interface: Intel Corporation NM10/ICH7 Family SATA Controller [IDE mode] (rev 01)
O comando, route -n, apresentou a seguinte mensagem:
Tabela de Roteamento IP do Kernel
Destino Roteador MáscaraGen. Opções Métrica Ref Uso Iface
O comando, cat /etc/network/interfaces, apresentou a seguinte mensagem:
# interfaces(5) file used by ifup(
and ifdown(
auto lo
iface lo inet loopback
O comando, cat /etc/resolv.conf, apresentou a seguinte mensagem:
# Dynamic resolv.conf(5) file for glibc resolver(3) generated by resolvconf(
# DO NOT EDIT THIST FILE BY HAND -- YOUR CHANGES WILL BE OVERWRITTEN
O seguinte comando, nmcli dev list eth0, apresentou a mensagem:
Usage: nmcli device { COMMAND | help }
COMMAND := { status | show | connect | reapply | disconnect | delete | monitor | wifi | lldp }
status
show [<ifname>]
set [ifname] <ifname> [ autoconnect yes|no] [managed yes|no]
connect <ifname>
reapply <ifname>
disconnect <ifname>
delete <ifname>
monitor <ifname>
wifi [list [ifname <ifname>] [bssid <BSSID>]]
wifi connect <(B)SSID> [password <password>] [wep-key-type key|phrase] [ifname <ifname>]
[bssid <BSSID>] [name <name>] [private yes|no] [hidden yes|no]
wifi hotspot [ifname <ifname>] [con-name <name>] [ssid <SSID>] [band a|bg] [channel <channel>] [password <password>]
wifi rescan [ifname <ifname>] [[ssid <SSID to scan>] ...]
lldp [list [ifname <ifname>]]
Erro: comando "dev list" é inválido.
[/list][/list]