Como configurar um modem e uma placa de som ISA?

[cesar.biasi]

Estou rodando o ubuntu 5.04 num Pentium MMX 233MHz, e possuo um modem U.S.Robotics Inc. Sportster 56000 FAX Internal, da 3Com. Também possuo uma placa de Som com entrada para joystick e modem imbutido da Creative Labs, uma Creative Sound Blaster 16 com Creative Modem Blaster 33.6Kbps.
Ambas as placas são ISA e Plug-in-Play.
Já instalei o isapnp tools, o modconf e o modutils(dependecia), no bash dei as seguintes instruções:

#pnpdump --config > /etc/isapnp.conf
(nada apareceu, como é de se esperar quando tudo da certo como vi no site do debian) depois;

#isapnp /etc/isapnp.conf
(apareceu uns dados, pelo que eu vi no site do debian, devem ser as portas, IRQs e DMAs que as duas placas estão usando. Porém não apareceu a mensagem "Enable OK" como deveria se ser se tudo estivesse configurado certo. Parece que está ocorrendo conflito de IRQs e também de portas, ambas querendo usar a COM4)

Gostaria de ajuda para resolver esse conflito e decobrir que módulos eu devo carregar no modconf para que elas funcionem.
Também gostaria de saber se este procedimento basta para que elas funcionem.

Obs: O modem da placa de som, tem um plug de saída em outro padrão, portanto eu não uso ele, até por causa da velocidade que é maior no outro.

Segue o isapnp.conf para ajudar:

# $Id: pnpdump_main.c,v 1.27 2001/04/30 21:54:53 fox Exp $
# Release isapnptools-1.26
#
# This is free software, see the sources for details.
# This software has NO WARRANTY, use at your OWN RISK
#
# For details of the output file format, see isapnp.conf(5)
#
# For latest information and FAQ on isapnp and pnpdump see:
# http://www.roestock.demon.co.uk/isapnptools/
#
# Compiler flags:  -DREALTIME -DHAVE_PROC -DENABLE_PCI -DHAVE_SCHED_SETSCHEDULER -DHAVE_NANOSLEEP -DWANT_TO_VALIDATE
#
# Trying port address 0273
# Board 1 has serial identifier c8 0a 2c 36 36 02 30 8c 0e
# Board 2 has serial identifier 7f c7 d0 f5 97 30 20 72 56

# (DEBUG)
(READPORT 0x0273)
(ISOLATE PRESERVE)
(IDENTIFY *)
(VERBOSITY 2)
(CONFLICT (IO FATAL)(IRQ FATAL)(DMA FATAL)(MEM FATAL)) # or WARNING

# Card 1: (serial identifier c8 0a 2c 36 36 02 30 8c 0e)
# Vendor Id CTL3002, Serial Number 170669622, checksum 0xC8.
# Version 1.0, Vendor version 3.0
# ANSI string -->Creative Phone Blaster 28.8/33.6<--
#
# Logical device id CTL0031
#     Device supports vendor reserved register @ 0x3a
#     Device supports vendor reserved register @ 0x3b
#     Device supports vendor reserved register @ 0x3e
#     Device supports vendor reserved register @ 0x3f
#
# Edit the entries below to uncomment out the configuration required.
# Note that only the first value of any range is given, this may be changed if required
# Don't forget to uncomment the activate (ACT Y) when happy

(CONFIGURE CTL3002/170669622 (LD 0
#     ANSI string -->Audio<--

# Multiple choice time, choose one only !

#     Start dependent functions: priority preferred
#       IRQ 5.
#             High true, edge sensitive interrupt (by default)
# (INT 0 (IRQ 5 (MODE +E)))
#       First DMA channel 1.
#             8 bit DMA only
#             Logical device is a bus master
#             DMA may execute in count by byte mode
#             DMA may not execute in count by word mode
#             DMA channel speed in compatible mode
# (DMA 0 (CHANNEL 1))
#       Next DMA channel 5.
#             16 bit DMA only
#             Logical device is not a bus master
#             DMA may not execute in count by byte mode
#             DMA may execute in count by word mode
#             DMA channel speed in compatible mode
# (DMA 1 (CHANNEL 5))
#       Logical device decodes 16 bit IO address lines
#             Minimum IO base address 0x0220
#             Maximum IO base address 0x0220
#             IO base alignment 1 bytes
#             Number of IO addresses required: 16
# (IO 0 (SIZE 16) (BASE 0x0220))
#       Logical device decodes 16 bit IO address lines
#             Minimum IO base address 0x0330
#             Maximum IO base address 0x0330
#             IO base alignment 1 bytes
#             Number of IO addresses required: 2
# (IO 1 (SIZE 2) (BASE 0x0330))
#       Logical device decodes 16 bit IO address lines
#             Minimum IO base address 0x0388
#             Maximum IO base address 0x0388
#             IO base alignment 1 bytes
#             Number of IO addresses required: 4
# (IO 2 (SIZE 4) (BASE 0x0388))

#       Start dependent functions: priority acceptable
#       IRQ 5, 7 or 10.
#             High true, edge sensitive interrupt (by default)
# (INT 0 (IRQ 5 (MODE +E)))
#       First DMA channel 0, 1 or 3.
#             8 bit DMA only
#             Logical device is a bus master
#             DMA may execute in count by byte mode
#             DMA may not execute in count by word mode
#             DMA channel speed in compatible mode
# (DMA 0 (CHANNEL 0))
#       Next DMA channel 5, 6 or 7.
#             16 bit DMA only
#             Logical device is a bus master
#             DMA may not execute in count by byte mode
#             DMA may execute in count by word mode
#             DMA channel speed in compatible mode
# (DMA 1 (CHANNEL 5))
#       Logical device decodes 16 bit IO address lines
#             Minimum IO base address 0x0220
#             Maximum IO base address 0x0280
#             IO base alignment 32 bytes
#             Number of IO addresses required: 16
# (IO 0 (SIZE 16) (BASE 0x0220))
#       Logical device decodes 16 bit IO address lines
#             Minimum IO base address 0x0300
#             Maximum IO base address 0x0330
#             IO base alignment 48 bytes
#             Number of IO addresses required: 2
# (IO 1 (SIZE 2) (BASE 0x0300))
#       Logical device decodes 16 bit IO address lines
#             Minimum IO base address 0x0388
#             Maximum IO base address 0x0388
#             IO base alignment 1 bytes
#             Number of IO addresses required: 4
# (IO 2 (SIZE 4) (BASE 0x0388))

#       Start dependent functions: priority acceptable
#       IRQ 5, 7 or 10.
#             High true, edge sensitive interrupt (by default)
# (INT 0 (IRQ 5 (MODE +E)))
#       First DMA channel 0, 1 or 3.
#             8 bit DMA only
#             Logical device is a bus master
#             DMA may execute in count by byte mode
#             DMA may not execute in count by word mode
#             DMA channel speed in compatible mode
# (DMA 0 (CHANNEL 0))
#       Next DMA channel 5, 6 or 7.
#             16 bit DMA only
#             Logical device is a bus master
#             DMA may not execute in count by byte mode
#             DMA may execute in count by word mode
#             DMA channel speed in compatible mode
# (DMA 1 (CHANNEL 5))
#       Logical device decodes 16 bit IO address lines
#             Minimum IO base address 0x0220
#             Maximum IO base address 0x0280
#             IO base alignment 32 bytes
#             Number of IO addresses required: 16
# (IO 0 (SIZE 16) (BASE 0x0220))
#       Logical device decodes 16 bit IO address lines
#             Minimum IO base address 0x0300
#             Maximum IO base address 0x0330
#             IO base alignment 48 bytes
#             Number of IO addresses required: 2
# (IO 1 (SIZE 2) (BASE 0x0300))

#       Start dependent functions: priority functional
#       IRQ 5, 7 or 10.
#             High true, edge sensitive interrupt (by default)
# (INT 0 (IRQ 5 (MODE +E)))
#       First DMA channel 0, 1 or 3.
#             8 bit DMA only
#             Logical device is not a bus master
#             DMA may execute in count by byte mode
#             DMA may not execute in count by word mode
#             DMA channel speed in compatible mode
# (DMA 0 (CHANNEL 0))
#       Next DMA channel 5, 6 or 7.
#             16 bit DMA only
#             Logical device is a bus master
#             DMA may not execute in count by byte mode
#             DMA may execute in count by word mode
#             DMA channel speed in compatible mode
# (DMA 1 (CHANNEL 5))
#       Logical device decodes 16 bit IO address lines
#             Minimum IO base address 0x0220
#             Maximum IO base address 0x0280
#             IO base alignment 32 bytes
#             Number of IO addresses required: 16
# (IO 0 (SIZE 16) (BASE 0x0220))

#       Start dependent functions: priority functional
#       IRQ 5, 7 or 10.
#             High true, edge sensitive interrupt (by default)
# (INT 0 (IRQ 5 (MODE +E)))
#       First DMA channel 0, 1 or 3.
#             8 bit DMA only
#             Logical device is a bus master
#             DMA may execute in count by byte mode
#             DMA may not execute in count by word mode
#             DMA channel speed in compatible mode
# (DMA 0 (CHANNEL 0))
#       Logical device decodes 16 bit IO address lines
#             Minimum IO base address 0x0220
#             Maximum IO base address 0x0280
#             IO base alignment 32 bytes
#             Number of IO addresses required: 16
# (IO 0 (SIZE 16) (BASE 0x0220))
#       Logical device decodes 16 bit IO address lines
#             Minimum IO base address 0x0300
#             Maximum IO base address 0x0330
#             IO base alignment 48 bytes
#             Number of IO addresses required: 2
# (IO 1 (SIZE 2) (BASE 0x0300))
#       Logical device decodes 16 bit IO address lines
#             Minimum IO base address 0x0388
#             Maximum IO base address 0x0388
#             IO base alignment 1 bytes
#             Number of IO addresses required: 4
# (IO 2 (SIZE 4) (BASE 0x0388))

#       Start dependent functions: priority functional
#       IRQ 5, 7 or 10.
#             High true, edge sensitive interrupt (by default)
# (INT 0 (IRQ 5 (MODE +E)))
#       First DMA channel 0, 1 or 3.
#             8 bit DMA only
#             Logical device is not a bus master
#             DMA may execute in count by byte mode
#             DMA may not execute in count by word mode
#             DMA channel speed in compatible mode
# (DMA 0 (CHANNEL 0))
#       Logical device decodes 16 bit IO address lines
#             Minimum IO base address 0x0220
#             Maximum IO base address 0x0280
#             IO base alignment 32 bytes
#             Number of IO addresses required: 16
# (IO 0 (SIZE 16) (BASE 0x0220))
#       Logical device decodes 16 bit IO address lines
#             Minimum IO base address 0x0300
#             Maximum IO base address 0x0330
#             IO base alignment 48 bytes
#             Number of IO addresses required: 2
# (IO 1 (SIZE 2) (BASE 0x0300))

#       Start dependent functions: priority functional
#       IRQ 5, 7, 10 or 11.
#             High true, edge sensitive interrupt (by default)
# (INT 0 (IRQ 5 (MODE +E)))
#       First DMA channel 0, 1 or 3.
#             8 bit DMA only
#             Logical device is a bus master
#             DMA may execute in count by byte mode
#             DMA may not execute in count by word mode
#             DMA channel speed in compatible mode
# (DMA 0 (CHANNEL 0))
#       Logical device decodes 16 bit IO address lines
#             Minimum IO base address 0x0220
#             Maximum IO base address 0x0280
#             IO base alignment 32 bytes
#             Number of IO addresses required: 16
# (IO 0 (SIZE 16) (BASE 0x0220))

#     End dependent functions
(NAME "CTL3002/170669622[0]{Audio               }")
# (ACT Y)
))
#
# Logical device id CTL2011
#     Device supports vendor reserved register @ 0x3a
#     Device supports vendor reserved register @ 0x3b
#     Device supports vendor reserved register @ 0x3e
#     Device supports vendor reserved register @ 0x3f
#
# Edit the entries below to uncomment out the configuration required.
# Note that only the first value of any range is given, this may be changed if required
# Don't forget to uncomment the activate (ACT Y) when happy

(CONFIGURE CTL3002/170669622 (LD 1
#     Compatible device id PNP0600
#     ANSI string -->IDE<--

# Multiple choice time, choose one only !

#     Start dependent functions: priority preferred
#       IRQ 10.
#             High true, edge sensitive interrupt (by default)
# (INT 0 (IRQ 10 (MODE +E)))
#       Logical device decodes 16 bit IO address lines
#             Minimum IO base address 0x0168
#             Maximum IO base address 0x0168
#             IO base alignment 1 bytes
#             Number of IO addresses required: 8
# (IO 0 (SIZE (BASE 0x0168))
#       Logical device decodes 16 bit IO address lines
#             Minimum IO base address 0x036e
#             Maximum IO base address 0x036e
#             IO base alignment 1 bytes
#             Number of IO addresses required: 2
# (IO 1 (SIZE 2) (BASE 0x036e))

#       Start dependent functions: priority acceptable
#       IRQ 11.
#             High true, edge sensitive interrupt (by default)
# (INT 0 (IRQ 11 (MODE +E)))
#       Logical device decodes 16 bit IO address lines
#             Minimum IO base address 0x01e8
#             Maximum IO base address 0x01e8
#             IO base alignment 1 bytes
#             Number of IO addresses required: 8
# (IO 0 (SIZE (BASE 0x01e8))
#       Logical device decodes 16 bit IO address lines
#             Minimum IO base address 0x03ee
#             Maximum IO base address 0x03ee
#             IO base alignment 1 bytes
#             Number of IO addresses required: 2
# (IO 1 (SIZE 2) (BASE 0x03ee))

#       Start dependent functions: priority acceptable
#       IRQ 10, 11 or 15.
#             High true, edge sensitive interrupt (by default)
# (INT 0 (IRQ 10 (MODE +E)))
#       Logical device decodes 16 bit IO address lines
#             Minimum IO base address 0x0180
#             Maximum IO base address 0x01b8
#             IO base alignment 8 bytes
#             Number of IO addresses required: 8
# (IO 0 (SIZE (BASE 0x0180))
#       Logical device decodes 16 bit IO address lines
#             Minimum IO base address 0x0306
#             Maximum IO base address 0x033e
#             IO base alignment 8 bytes
#             Number of IO addresses required: 2
# (IO 1 (SIZE 2) (BASE 0x0306))

#       Start dependent functions: priority functional
#       IRQ 15.
#             High true, edge sensitive interrupt (by default)
# (INT 0 (IRQ 15 (MODE +E)))
#       Logical device decodes 16 bit IO address lines
#             Minimum IO base address 0x0170
#             Maximum IO base address 0x0170
#             IO base alignment 1 bytes
#             Number of IO addresses required: 8
# (IO 0 (SIZE (BASE 0x0170))
#       Logical device decodes 16 bit IO address lines
#             Minimum IO base address 0x0376
#             Maximum IO base address 0x0376
#             IO base alignment 1 bytes
#             Number of IO addresses required: 1
# (IO 1 (SIZE 1) (BASE 0x0376))

#     End dependent functions
(NAME "CTL3002/170669622[1]{IDE                 }")
# (ACT Y)
))
#
# Logical device id CTL7fff
#     Device supports vendor reserved register @ 0x38
#     Device supports vendor reserved register @ 0x39
#     Device supports vendor reserved register @ 0x3b
#     Device supports vendor reserved register @ 0x3e
#     Device supports vendor reserved register @ 0x3f
#
# Edit the entries below to uncomment out the configuration required.
# Note that only the first value of any range is given, this may be changed if required
# Don't forget to uncomment the activate (ACT Y) when happy

(CONFIGURE CTL3002/170669622 (LD 2
#     ANSI string -->Reserved<--
#     Logical device decodes 16 bit IO address lines
#         Minimum IO base address 0x0304
#         Maximum IO base address 0x033c
#         IO base alignment 8 bytes
#         Number of IO addresses required: 1
# (IO 0 (SIZE 1) (BASE 0x0304))
(NAME "CTL3002/170669622[2]{Reserved            }")
# (ACT Y)
))
#
# Logical device id CTL7001
#     Device supports vendor reserved register @ 0x3a
#     Device supports vendor reserved register @ 0x3b
#     Device supports vendor reserved register @ 0x3e
#     Device supports vendor reserved register @ 0x3f
#
# Edit the entries below to uncomment out the configuration required.
# Note that only the first value of any range is given, this may be changed if required
# Don't forget to uncomment the activate (ACT Y) when happy

(CONFIGURE CTL3002/170669622 (LD 3
#     ANSI string -->Game<--
#     Logical device decodes 16 bit IO address lines
#         Minimum IO base address 0x0200
#         Maximum IO base address 0x0200
#         IO base alignment 1 bytes
#         Number of IO addresses required: 8
# (IO 0 (SIZE (BASE 0x0200))
(NAME "CTL3002/170669622[3]{Game                }")
# (ACT Y)
))
#
# Logical device id CTL3001
#     Device supports vendor reserved register @ 0x38
#     Device supports vendor reserved register @ 0x39
#     Device supports vendor reserved register @ 0x3b
#     Device supports vendor reserved register @ 0x3e
#     Device supports vendor reserved register @ 0x3f
#
# Edit the entries below to uncomment out the configuration required.
# Note that only the first value of any range is given, this may be changed if required
# Don't forget to uncomment the activate (ACT Y) when happy

(CONFIGURE CTL3002/170669622 (LD 4
#     ANSI string -->COM<--

# Multiple choice time, choose one only !

#     Start dependent functions: priority preferred
#       IRQ 3, 4, 5, 7, 10, 11 or 15.
#             High true, edge sensitive interrupt (by default)
# (INT 0 (IRQ 3 (MODE +E)))
#       Logical device decodes 16 bit IO address lines
#             Minimum IO base address 0x03e8
#             Maximum IO base address 0x03e8
#             IO base alignment 1 bytes
#             Number of IO addresses required: 8
# (IO 0 (SIZE (BASE 0x03e8))

#       Start dependent functions: priority acceptable
#       IRQ 3, 4, 5, 7, 10, 11 or 15.
#             High true, edge sensitive interrupt (by default)
# (INT 0 (IRQ 3 (MODE +E)))
#       Logical device decodes 16 bit IO address lines
#             Minimum IO base address 0x02e8
#             Maximum IO base address 0x02e8
#             IO base alignment 1 bytes
#             Number of IO addresses required: 8
# (IO 0 (SIZE (BASE 0x02e8))

#       Start dependent functions: priority acceptable
#       IRQ 3.
#             High true, edge sensitive interrupt (by default)
# (INT 0 (IRQ 3 (MODE +E)))
#       Logical device decodes 16 bit IO address lines
#             Minimum IO base address 0x02f8
#             Maximum IO base address 0x02f8
#             IO base alignment 1 bytes
#             Number of IO addresses required: 8
# (IO 0 (SIZE (BASE 0x02f8))

#       Start dependent functions: priority acceptable
#       IRQ 4.
#             High true, edge sensitive interrupt (by default)
# (INT 0 (IRQ 4 (MODE +E)))
#       Logical device decodes 16 bit IO address lines
#             Minimum IO base address 0x03f8
#             Maximum IO base address 0x03f8
#             IO base alignment 1 bytes
#             Number of IO addresses required: 8
# (IO 0 (SIZE (BASE 0x03f8))

#       Start dependent functions: priority functional
#       IRQ 3, 4, 5, 7, 10, 11 or 15.
#             High true, edge sensitive interrupt (by default)
# (INT 0 (IRQ 3 (MODE +E)))
#       Logical device decodes 16 bit IO address lines
#             Minimum IO base address 0x02a0
#             Maximum IO base address 0x02d8
#             IO base alignment 8 bytes
#             Number of IO addresses required: 8
# (IO 0 (SIZE (BASE 0x02a0))

#     End dependent functions
(NAME "CTL3002/170669622[4]{COM                 }")
# (ACT Y)
))
# End tag... Checksum 0x00 (OK)

# Card 2: (serial identifier 7f c7 d0 f5 97 30 20 72 56)
# Vendor Id USR2030, Serial Number 3352360343, checksum 0x7F.
#     Version 1.0, Vendor version 0.0
#     ANSI string -->U.S.Robotics Inc. Sportster 56000 FAX Internal <--
#
# Logical device id USR2030
#     Device supports vendor reserved register @ 0x38
#     Device supports vendor reserved register @ 0x39
#     Device supports vendor reserved register @ 0x3b
#     Device supports vendor reserved register @ 0x3e
#     Device supports vendor reserved register @ 0x3f
#
# Edit the entries below to uncomment out the configuration required.
# Note that only the first value of any range is given, this may be changed if required
# Don't forget to uncomment the activate (ACT Y) when happy

(CONFIGURE USR2030/3352360343 (LD 0

# Multiple choice time, choose one only !

#     Start dependent functions: priority preferred
#       Logical device decodes 16 bit IO address lines
#             Minimum IO base address 0x02f8
#             Maximum IO base address 0x02f8
#             IO base alignment 8 bytes
#             Number of IO addresses required: 8
# (IO 0 (SIZE (BASE 0x02f8))
#       IRQ 3, 5 or 7.
#             High true, edge sensitive interrupt (by default)
# (INT 0 (IRQ 3 (MODE +E)))

#       Start dependent functions: priority acceptable
#       Logical device decodes 16 bit IO address lines
#             Minimum IO base address 0x03f8
#             Maximum IO base address 0x03f8
#             IO base alignment 8 bytes
#             Number of IO addresses required: 8
# (IO 0 (SIZE (BASE 0x03f8))
#             *** Bad resource data (Clarifications 4.6.2): IRQ 2 invalid, changing to 9
#       IRQ 3, 4, 5, 7 or 9.
#             High true, edge sensitive interrupt (by default)
# (INT 0 (IRQ 3 (MODE +E)))

#       Start dependent functions: priority acceptable
#       Logical device decodes 16 bit IO address lines
#             Minimum IO base address 0x03e8
#             Maximum IO base address 0x03e8
#             IO base alignment 8 bytes
#             Number of IO addresses required: 8
# (IO 0 (SIZE (BASE 0x03e8))
#             *** Bad resource data (Clarifications 4.6.2): IRQ 2 invalid, changing to 9
#       IRQ 3, 4, 5, 7 or 9.
#             High true, edge sensitive interrupt (by default)
# (INT 0 (IRQ 3 (MODE +E)))

#       Start dependent functions: priority acceptable
#       Logical device decodes 16 bit IO address lines
#             Minimum IO base address 0x02e8
#             Maximum IO base address 0x02e8
#             IO base alignment 8 bytes
#             Number of IO addresses required: 8
# (IO 0 (SIZE (BASE 0x02e8))
#             *** Bad resource data (Clarifications 4.6.2): IRQ 2 invalid, changing to 9
#       IRQ 3, 4, 5, 7 or 9.
#             High true, edge sensitive interrupt (by default)
# (INT 0 (IRQ 3 (MODE +E)))

#     End dependent functions
(NAME "USR2030/3352360343[0]{U.S.Robotics Inc. Sportster 56000 FAX Internal }")
# (ACT Y)
))
# End tag... Checksum 0x00 (OK)

# Returns all cards to the "Wait for Key" state
(WAITFORKEY) :roll:

[duff2004]

Estou com um problema muito parecido com o seu. Consegui fazer o isapnp detectar o hardware e mostrar a mensagem com enabled-ok após descomentar no isapnp.conf as linhas "(ACT Y) ". A placa de som consegui fazer funcionar após carregar o módulo com o comando modprobe snd-awe64 (acho que é isso, não estou no computador com o problema agora).
Porém, o modem não tem jeito de funcionar. O meu é um hardmodem Diamond Supra Express 56i sp. Não consigo configurar os jumpers por não possuir mais o manual. Já pesquisei bastante no google e apenas encontrei informações de que o modem é compatível.

Tentei seguir os passos dos tutoriais que encontrei, mas todos encerram no momento em que o isapnp detecta as placas (até aí cheguei).

Depois disso, tentei configurar com o pppconfig e o modem não comunicou em nenhuma das portas (ttyS1, etc). O mesmo se deu com o gnome-ppp.Também tentei crial link no /dev/modem para as portas tt..... e também não funcionou.

Você já resolveu o seu problema?

Agradeço antecipadamente se alguém souber fornecer a solução para o problema.

Obs: estou usando o Xubuntu com a base de instalação do Breezy

[cesar.biasi]

Bem quanto ao modem, eu consegui fazer funcionar, e escrevi um tutorial sobre o assunto. Ele está na parte de Hardwares e Periféricos e possui uma cópia na parte de Tutoriais, Dicas e truques. O título do tópico é: Instalando e Configurando um Hardmodem ISA!!!!!

Acho que isso conseguirá resolver o seu problema. Desculpe ter demorado tando para achar uma solução. É que eu tive que fazer primeiro uns upgrades no hardware da minha máquina para que o Ubuntu ficasse possível de usar na minha máquina; e eu também andava meio sem tempo pra ficar fuçando na net pra descobrir como fazer. Tive que fuçar muito no ubuntu para descobrir quais eram os arquivos certos, pois de uma distribuição para outra, os nomes de certos arquivos podem mudar, além do fato de serem muito poucas as pessoas que sabem onde fica cada arquivo de configuração e o que ele configura, além de contar com a sorte para achar sozinho certos arquivos de configuração e descobrir para que servem. Tive que mesclar a informação contida em três tutoriais do Slackware para fazer o modem U.S. Robotics Sporster 56000 funcionar no meu micro.

Espero que te ajude. Agora, quanto a placa de Som, eu tenho uma Creative Phone Blaster 33.6. Mistura de Modem + Placa de Som. O modem desta placa eu não estou usando, por isso eu nem o ativei no isapnp.conf. Eu ainda não consegui fazer ela funcionar; eu carrego todas as IRQs, portas e DMAs no isapnp.conf , aparece Enable OK em tudo, dou dmesg, e o Ubuntu reconhece as duas placas; Som e modem US robotics, mas quando eu vou carregar o módulo de som, seja o do alsa o sb.ko ou o do OSS, o snd-sb16.ko; o modprobe acusa (device no such). Tentei usar o modulo que você falou, o snd-awe64 através do modprobe, mas ele acusa módulo não encontrado.
Será que está placa não tem módulo para o Ubuntu, ou pior para o Linux, ou eu esto errando no jeito de instalar e configurar a placa? Pelo o que eu pude ver, você conseguiu resolver esse problema, se você puder me ajudar eu agradeceria, Obrigado!